Panasonic WJ-NV200K - Login operation at startup

17
This product is designed to be used indoors.
Do not place this product in the following places:
 • Locationsexposedtodirectsunlight
 • Locationssubjecttohavingstrongvibrationorimpact
 • Locationsnearmagneticfieldsourcessuchasatelevi-
sion or speakers
 • Locationswherecondensationformseasily,wheretem-
perature changes greatly or where humidity level is high
 • Locationssubjecttosteamandoilsmokesuchasa
kitchen
 • Locationswhicharenotlevel
 • Locationssubjecttodust
 • Locationswhereitmaygetwetfromrainorwatersplash
Do not install this product in locations where the prod-
uct or the cables can be destroyed or damaged by
persons with malicious intent.
Place this product horizontally on a level surface.
Do not place this product in an upright position. When
stacking multiple recorders, clear a space of more than 5 cm
{2 inches} from both sides, the top, the bottom and the rear
of them.
Heat dissipation
To prevent this product from overheating, heed the following.
Failure to observe this may cause fire or trouble.
 • Donotblocktheventilationopenings.Maintaintheprod-
uct periodically to prevent dust from blocking openings.
 • Thelifetimeofthecoolingfanislimitedbyuse.Itisrec-
ommended to replace them after approx. 30 000 hours
of operation. Contact your dealer for replacement of the
cooling fans.
 • Clearaspaceofmorethan5cm{2inches}fromboth
sides, the top, and the rear of the product. Do not block
the ventilation openings on the front side since this prod-
uct is designed to cool the hard disk drives by inhaling
air from the front.
Avoid placing this product near noise sources
If the cables are placed near noise sources such as fluores-
cent lamps, noises may be produced. In this case, rewire
avoiding the noise sources, or move the product to a place
far from the source.
Grounding
Confirm that the wire is connected from the SIGNAL GND
terminal to earth ground.
A grounding connection must be made before connecting
the power plug or this product to the main power supply.
When disconnecting the grounding wire, make sure that the
power plug of this product is disconnected from the main
power supply.
For BNC cable connection
Use only the recommended plug below when connecting the
BNC plug to the connectors on the rear panel of the record-
er.
Applicable plug MIL-C39012C, MIL-C39012/16F or BS
CECC2212: 1981
* Suffixes attached to the standards may be updated.
Tip dimensions inside the recommended BNC plug
Important:
 • Acompatibleplugshallbeused.Failuretoobservethis
may cause trouble such as poor contact. At worst, the
connector of this product may be damaged.
Avoid placing receptacles that contain liquids such as
water near this product.
If liquid spills onto this product, it may cause fire or an elec-
tric shock.
"
More than
5 cm {2 inches}
More than
5 cm {2 inches}
More than
5 cm {2 inches}
Precautions for installation
Plug (locally procured)
BNC cable (locally procured)
ø1.32 mm - ø1.37 mm
{ø0.052" - ø0.054"}
ø0.13 mm - ø0.69 mm
{ø0.005" - ø0.027"}
Plug (locally procured)
BNC cable (locally procured)
ø1.32 mm - ø1.37 mm
{ø0.052" - ø0.054"}
ø0.13 mm - ø0.69 mm
{ø0.005" - ø0.027"}