Paradox Spectra SP4000 Programming Guide

Magellan / Spectra SP 41
Installer Function Keys
Use the following instructions to access the Installer Function features.
RF jamming 3 344 - RF receiver jam detection XH - RF Jamming Restoral
GSM/GPRS module Rf interference restore 3 552 - Radio transmitter restore YK - Communication restore
GSM/GPRS network restore 3 552 - Radio transmitter restore YK - Communication restore
GSM/GPRS supervision restore 3 552 - Radio transmitter restore YK - Communication restore
GSM/GPRS fail to communicate restore 3 354 - Communication restore YK - Fail to communicate restore
IP network restore 3 552 - Radio transmitter restore YK - Communication restore
IP supervision restore 3 552 - Radio transmitter restore YK - Communication restore
IP fail to communicate restore 3 354 - Communication restore YK - Fail to communicate restore
Combus fault 1 333 - Expansion module failure ET - Expansion trouble
Module tamper 1 341 - Expansion module tamper TA - Tamper alarm
Module AC fail 1 342 - AC failure on module AT - Module AC fail
Module battery fail 1 338 - Battery failure on module YT - Module battery fail
Bus fault restore 3 333 - Expansion module failure restore ER - Expansion restoral
Module tamper restore 3 341 - Expansion module tamper restore TR - Tamper restoral
Module AC fail restore 3 342 - AC restored on module AR - Module AC fail restore
Module battery fail restore 3 338 - Battery failure on module YR - Module battery fail restore
Cold start 1 3A8 - System shutdown RR - Power up
Test report engaged 1 6A2 - Periodic test report TX - Test report
PC software communication finished 1 412 - Successful - download access RS - Remote program success
Installer on site 1 627 - Program mode entry LB - Local program
Installer programming finished 1 628 - Program mode exit LS - Local program success
Maintenance in 1 627 - Program mode entry LB - Local program
Maintenance out 1 628 - Program mode exit LS - Local program success
Closing delinquency 1 654 - System inactivity CD - System inactivity
Manual trigger test in 1 6A1 - Manual trigger test in TS - Manual trigger test in
Manual trigger test out 3 6A1 - Manual trigger test out TS - Manual trigger test out
Exit error 1 374 - Exit error EE - Exit error
RF module low battery 1 384 - RF transmitter low battery XT - Transmitter battery trouble
RF module battery restore 3 384 - RF transmitter battery restore XR - Transmitter battery restoral
RF zone supervision lost 1 381 - Loss of supervision - RF US - Untype zone supervision
RF zone supervision restore 3 381 - Supervision restore - RF UR - Untyped zone restoral
RF module supervision lost 1 381 - Loss of supervision- RF US - Untype zone supervision
RF module supervision restore 3 381 - Loss of supervision- RF restore UR - Untyped zone restoral
RF module tamper 1 145 - Expansion module tamper ES - Expansion device tamper
RF module tamper restore 3 145 - Expansion module tamper restore EJ - Expansion device restore
Paramedic alarm 1 1AA - Medical MA - Medical alarm
Zone forced 1 57A - Zone forced XW - Zone forced
Zone included 3 57A - Zone included UU - Zone included
Function Action Description
Test Report
[
ENTER]+[INSTALLER CODE] + [MEM]
Send the “Test Report” report code programmed in section [875]
(page 38) to the monitoring station
Cancel Communication
[
ENTER]+[INSTALLER CODE] + [STAY]
Cancels all communication with the WinLoad / BabyWare software or
with the monitoring station until the next reportable event
Answer WinLoad /
BabyWare Software
[
ENTER]+[INSTALLER CODE] + [SLEEP]
Will force the console to answer an incoming call from the monitoring
station that is using the WinLoad / BabyWare software
Call WinLoad / BabyWare
Software
[
ENTER]+[INSTALLER CODE] + [BYP]
Will dial the PC telephone number programmed in section [915]
(page 22) in order to initiate communication with a computer using
the WinLoad / BabyWare software
Installer Test Mode
[ENTER]+[INSTALLER CODE] + [TBL]
The installer test mode will allow you to perform walk tests where the
siren will squawk to indicate opened zones. Press the [TBL] key
again to exit
System Event Default Contact ID Report Code Default SIA Report Code

Paradox Spectra SP4000 Specifications

General

Partitions	2
User Codes	32
Event Buffer	256 events
StayD Mode	Yes
Expandable via Expansion Modules	Yes
Bus	Yes, 4-wire expansion bus
Battery Backup	12V 7Ah
PGM Outputs	2