Pioneer XR-P770F Operating Instructions

TURNING ON THE POWER
Operations indicated by the [ G ] mark are performed with the
remote control unit.
e@Read “CONNECTIONS” again and ensure that speakers,
antenna, etc., are connected properly.
Press the POWER switch.
To switch the power OFF: .
Press the POWER switch again and the STANDBY indicator lights.
You cannot see the clock display in this unit.
Press the DISPLAY/RDS CLOCK ADJ button to see the clock
display.
Turning power ON without using the POWER switch
Performing any of the following operations while the system
power is off (STANDBY) turns the power ON.
If a CD has been loaded, it
starts to play.
The tuner (radio) input is
selected.
If a cassette tape has been
loaded, it starts to play.
Ifthe connected component
is operating, it startsto play.
Play starts if there is a CD in
the selected 5-disc access.
The function which has
been selected beforethe last
time the power was
switched off is selected and
the corresponding opera-
tion starts.
@When power is OFF (Standby), press the SLOT EJECT button,
and power switches ON, letting you remove a disc. Also, when
power is OFF (Standby), if you load a CD in the Plus 1 Disc Slot,
Power automatically switches ON, and play starts.
TUNING INTO STATIONS
@ Be sure to connect the antennas.
eDo not place the AM antenna on a metallic case including the
receiver cabinet or near a CD player, LD player, DAT recorder,
personal computer or TV set. Any of these installations will
cause noise in reception.
|
i
=,
|
:
f
1. Press the tuner (FM/AM) function button.
Select the FM or AM broadcasting band.
Each time you press this button, FM and AMchangesalternately.
eee ec ees
2. Tunein the desired station by pressing the C-) or (= button.
e@ Manual tuning
Tap the C=) or (=) button in quick repetitions.
e Auto tuning
Press the C=) or C=) button for a second or two and remove your
finger from it when the frequency starts to change.
—The frequency changes automatically. When astationis received,
the
frequency
stops
changing
and
“TUNED”
appears
on
the
display.
e High-speed manual tuning
Press and hold the C=) or (3 button.
>The
frequency
changes
continuously
and
stops
when
your
finger
is
removed
from
the
button.
MONO button (Remote control unit only)
During
FM
reception:
Switches
between
stereo
and
monaural
modes
when
listening
to-a
stereo
broadcast.
If
there
is
a
lot
of
noise
in
the
stereo
position,
switch
to
MONO,
and
the
noise
will
be
suppressed.
Beat cut function
If
noise
occurs
during
recording
an
AM
broadcast,
perform
the
foliowing
procedures
to
reduce
the
noise.
1.
Press
the
POWER
switch
on
this
unit
so
that
the
STANDBY
indicator
lights
up.
2.
Turn
on
the
power
while
pressing
the
STATION
MEMORY
button.
(The
BEAT
CUT
indicator
lights.)
@To cancel the BEAT CUT function, repeat steps 1 and 2.
AM ]954_
BEAT CUT indicator lights.
11
<ARB7110>

Pioneer XR-P770F Specifications

Amplifier Section

continuous power output (RMS)	100 W + 100 W
channels	2 channels (stereo)
continuous power output (DIN)	80 W + 80 W

Power

power requirements	AC 230 V, 50/60 Hz
power consumption	530 W
music power (DIN)	115 W + 115 W

FM Tuner Section

reception frequencies (FM)	87.5 MHz to 108 MHz
reception frequencies (AM)	531 kHz to 1, 602 kHz (9 kHz step)
frequency response (Type II tape)	35 Hz to 15, 000 Hz +6 dB

Weight and Dimensions

external dimensions	260 (W) x 310 (H) x 371.5 (D) mm
weight	11.5 kg
antenna input	75 Ω unbalanced