What to do if Powtran DC Drives show Err.07?
If your Powtran DC Drive displays Err.07, it indicates overvoltage during normal operation. Here's what you should do: * Cancel any external force dragging the motor or install a braking resistor. * Set the voltage to the normal range if the input voltage is too high.
How to fix Powtran DC Drives Err.18?
If your Powtran DC Drive displays Err.18: * Replace the drive panel. * Replace hall device.
What to do if Powtran DC Drives show Err.12?
If your Powtran DC Drive displays Err.12: * Replace the drive, the power board or contactor if the drive panel is abnormal. * Seek for technical support if the lightning protection plate is abnormal. * Check and eliminate the existing problems in the peripheral line if the main control panel is abnormal.
What does Err.08 mean on Powtran DC Drives?
If your Powtran DC Drive displays Err.08, it means that the input voltage is out of the specified range. Adjust the voltage to meet the specification requirements.
How do I resolve Powtran DC Drives Err.19?
If your Powtran DC Drive displays Err.19, it indicates a motor parameter setting error. To correct this: * Set motor parameters according to the motor's nameplate. * Check the lead wire from the inverter to the motor if the parameter identification process times out.
How to troubleshoot Powtran DC Drives Err.17?
If your Powtran DC Drive displays Err.17, it indicates an input phase loss. To resolve this: * Check and eliminate any existing problems in the peripheral line. * Replace the drive, the power board or contactor if the drive plate and the contact are not normal.
What to do if Powtran DC Drives show Err.16?
If your Powtran DC Drive displays Err.16, it indicates a communication failure. Here's how to troubleshoot: * Check the communication cable. * Correctly set the communications expansion card type (F9.07). * Correctly set the communication parameters (F9 group). * Check the wiring of the host computer if it's not working properly.
What causes Powtran DC Drives to show Err.09?
If your Powtran DC Drive displays Err.09, it indicates a power failure. This can be caused by: * A momentary power cut: Reset the fault. * Inverter input voltage outside specification: Adjust the voltage to the normal range. * Abnormal bus voltage: Seek for technical support.
How to fix Powtran DC Drives Err.14?
If your Powtran DC Drive displays Err.14, it indicates an overheating issue. To resolve this: * Clean up the air duct if it's blocked. * Replace the fan if it's damaged. * Decrease the ambient temperature if it's too high. * Replace the thermistor if the module thermistor is damaged. * Replace the inverter module if it's damaged.
What to do if Powtran DC Drives show Err.02?
If your Powtran DC Drive displays Err.02, it indicates an overcurrent fault. This can occur due to several reasons. Here's what you should check: * Ensure the acceleration time isn't too short; increase it if necessary. * Adjust the manual torque boost or V/F curve if they're unsuitable. * Verify the voltage is within the normal range. * Eliminate any peripheral faults that may cause a short-circuit or earthing at the inverter output. * If using vector control, perform motor parameter identification. * If the motor is rotating and started unexpectedly, select Speed Tracking Start or restart after the motor has stopped. * Avoid sudden load increases during acceleration. * Consider upgrading to an inverter with a larger power level if the current one is undersized.
Check packing contents, nameplate for product model and order consistency.
Details critical safety warnings for installation, wiring, operation, and maintenance to prevent injury or damage.
Illustrates and names the components of the inverter's operation panel.
Describes the function and purpose of each key on the inverter's operation panel.
Provides step-by-step guides for viewing and modifying function codes and restoring factory settings.
Specifies required clearance dimensions for inverter installation based on power rating.
Illustrates the main circuit and control circuit connections for the frequency inverter.
Highlights critical safety measures and best practices for inverter wiring to prevent damage and hazards.
Lists parameters for configuring overcurrent, overvoltage, overload, and other protection settings.
Defines parameters for PID control adjustment, including feedback sources and gain settings.
Covers parameters specific to constant pressure water supply applications, like pump control and pressure settings.
Provides a table of fault IDs, failure types, possible causes, and solutions.
General| Output Voltage | 0 to rated input voltage |
|---|---|
| Power Range | 0.4kW to 400kW |
| Control Mode | V/F control |
| Frequency Range | 0~400Hz |
| Protection Functions | Overcurrent, Overvoltage, Undervoltage, Overload, Short circuit, Phase loss |
| Communication | RS485 (Modbus RTU protocol) |
| Cooling Method | Forced air cooling |
| Operating Temperature | -10℃~+40℃ (Derating if above 40℃) |
| Storage Temperature | -20℃~+60℃ |
| Humidity | 5% to 95% (non-condensing) |
| Altitude | Below 1000m (Derating if above 1000m) |
To Next Page