Proxim Tsunami 8000 series User Manual

Tsunami
®
800 & 8000 Series
(Point-to-point and Point-to-multipoint Products)
Software Management Guide
Products Covered
--> Tsunami
®
Multipoint
- MP-820-BSU-100
- MP-8100-BSU
- MP-8200-BSU; MP-8250-BS9; MP-8250-BS1
- MP-820-SUA-50
+
- MP-825-SUR-50
+
- MP-825-CPE-50
- MP-8100-SUA
- MP-8150-SUR
- MP-8150-SUR-100
- MP-8150-CPE
- MP-8200-SUA
- MP-8250-SUR
- MP-8160-BSU and MP-8160-BS9
- MP-8160-SUA
- MP-8160-CPE
--> Tsunami Quickbridge
®
- QB-8100-EPA / LNK
- QB-8150-EPR / LNK
- QB-8150-LNK-100
- QB-8150-LNK-12/50
- QB-8151-EPR / LNK
- QB-8200-EPA / LNK
- QB-8250-EPR / LNK
- QB-825-EPR / LNK-50
- QB-825-EPR / LNK-50
+

Proxim Tsunami 8000 series Specifications

General

Brand	Proxim
Model	Tsunami 8000 series
Category	Network Router
Language	English

Summary

2 Management and Monitoring Capabilities

2.1 Web (HTTP/HTTPS) Interface

Describes accessing device configuration via the web interface.

2.2 Command Line Interface

Explains using the CLI for device configuration and management.

2.2.1 HyperTerminal

2.3 Simple Network Management Protocol (SNMP) Management

Covers device management using SNMP and MIB files.

3 Device Initialization

3.1 Initialization

Explains the process of device initialization via various interfaces.

3.1.1 ScanTool

Describes using ScanTool for device discovery and IP configuration.

3.1.2 Initialize Device by using ScanTool

Provides steps for initializing devices using the ScanTool utility.

3.1.3 Modifying the IP Address of the Device by using ScanTool

Details how to change a device's IP address using ScanTool.

3.2 Logging onto the Web Interface

Guides users on how to log into the device's web interface.

3.2.2 COMMIT

Explains the COMMIT operation to apply configuration changes.

3.2.3 REBOOT

Details the REBOOT process for applying key parameter changes.

3.3 Factory Default Configuration

Lists the default configuration parameters for factory settings.

4 Basic Configuration

Basic Configuration

Provides access to minimum configuration parameters for network setup.

5 Advanced Configuration

5.1 System

5.2 Network

5.2.1 IP Configuration

5.2.1.1 Bridge Mode

5.2.1.2 Routing Mode

5.2.2 Static Route Table

5.2.3 Network Address Translation (NAT)

5.2.4 RIP

5.2.5 PPPoE End Point (SU Only)

5.2.6 IP over IP Tunneling

5.3 Ethernet

5.3.1 Basic Ethernet Configuration

5.3.2 Advanced Configuration

5.4 Wireless

5.4.1 Link Profiles

5.4.2 Wireless Outdoor Router Protocol (WORP)

5.4.3 Wireless Interface Properties

5.4.4 Dynamic Frequency Selection (DFS) / Dynamic Channel Selection (DCS)

Explains DFS and DCS for managing wireless channels and interference.

5.4.5 Roaming

Explains the roaming feature for seamless network services for mobile SUs.

5.4.6 BSU / SU Profiles

5.5 Security

5.5.1 Wireless Security

5.5.2 RADIUS

5.5.3 MAC ACL

5.6 Quality of Service (QoS)

Explains QoS for traffic prioritization and bandwidth allocation.

5.6.2 QoS Configuration

Covers the configuration of QoS features.

5.7 RADIUS Based SU QoS Configuration

5.8 VLAN (Bridge Mode Only)

Explains VLAN configuration in Bridge Mode.

5.8.1 System-Level VLAN Configuration

5.8.2 Ethernet VLAN Configuration

5.9 RADIUS Based SU VLAN Configuration

5.10 Filtering (Bridge Only)

Covers filtering mechanisms available in Bridge mode.

5.10.1 Protocol Filter