RichAuto A122 - Page 34

Add: 5F
, No.4 building, No 4. Yard, life Rd, life science park,
Tel：010-53275118 Fax
：
you finished
modification, the cursor will pass to the following row automatically, you could
modify all three axes pulse equivalent in turn by the way described above. Press “
to save all modifications you’ve made and return to the previous menu.
(2) Servo motor drive
The pulse equivalent factory defaults of X, Y, Z or A are all 400,
constant value and
set t
The numerator
of electronic gear ratio represents encoder resolution and could
be found in
servo drive instructions.
The denominator
of electronic gear ratio:

Lead screw drive: pulse equivalent(400)*lead screw pitch*transmission ratio

Spur rack drive: pulse
ratio
2. Table size
RichAuto
system make the table size as the soft limit values, in order to prevent
machine move over
travel
actual
value of machine
Setting method：
Enter
to be modified. Press “
X, Y, Z axis in order and then press “
3. Spindle delay(time)
Spindle delay (Unit:
ms)
4. Home setup
Home speed
: Each axis movement speed when execute return home.
X,Y axis home speed is 3000mm/min, and Z axis home speed is 1800mm/min.
Home sequence：
Each axis movement order when execute return home.
Including：
Z, X and Y
Z only
Y,X,Z
Y,X home
Beijing RichAuto S&T Co., Ltd
, No.4 building, No 4. Yard, life Rd, life science park,
Beiqing St., Changping d
ist.
：
010-53275110/53275111 Web site：
www.richnc.com.cn
modification, the cursor will pass to the following row automatically, you could
modify all three axes pulse equivalent in turn by the way described above. Press “
to save all modifications you’ve made and return to the previous menu.
The pulse equivalent factory defaults of X, Y, Z or A are all 400,
it can be
set t
he electronic gear ratio in servo motor drive.
of electronic gear ratio represents encoder resolution and could
servo drive instructions.
of electronic gear ratio:
Lead screw drive: pulse equivalent(400)*lead screw pitch*transmission ratio
Spur rack drive: pulse
equivalent
(400)t*rack module*gear teeth*pi*transmission
system make the table size as the soft limit values, in order to prevent
travel
，machine size value
must be less than or equal to the
value of machine
travel.
Enter
“Table Size”，press “ ” or“
”to move cursor to option
”，input the new numbers，press “
X, Y, Z axis in order and then press “
”to save all of the settings.
ms)
：
Including spindle on delay and spindle off delay.
: Each axis movement speed when execute return home.
X,Y axis home speed is 3000mm/min, and Z axis home speed is 1800mm/min.
Each axis movement order when execute return home.
Z,X,Y Z,Y,X
X and Y,Z X,Y,Z
XY home X,Y home
None home X home only
XZ and Y
Beijing RichAuto S&T Co., Ltd
ist.
Beijing, China
www.richnc.com.cn
30
modification, the cursor will pass to the following row automatically, you could
modify all three axes pulse equivalent in turn by the way described above. Press “
”
it can be
used as a
of electronic gear ratio represents encoder resolution and could
Lead screw drive: pulse equivalent(400)*lead screw pitch*transmission ratio
(400)t*rack module*gear teeth*pi*transmission
system make the table size as the soft limit values, in order to prevent
must be less than or equal to the
”to move cursor to option
”to save. Modify
”to save all of the settings.
Including spindle on delay and spindle off delay.
: Each axis movement speed when execute return home.
System default
X,Y axis home speed is 3000mm/min, and Z axis home speed is 1800mm/min.
Each axis movement order when execute return home.
XZ and Y