Rigol DS8000-R Series

To Next Page

To Previous Page

Chapter 5 To Trigger the Oscilloscope RIGOL

DS8000-R User Guide 5-53

Tip

If you enable both Trigger zone A and Trigger zone B, then perform the "A&&B"

operation, and it will become the final trigger condition.

Main Page

Safety Requirement4
- Safety Notices and Symbols6
- Measurement Category7
- Ventilation Requirement7
- Working Environment8
- Care and Cleaning9
- Environmental Considerations10
DS8000-R Series Overview11
Document Overview12
- Table of Contents15
Chapter 1 Quick Start23
- General Inspection24
- Appearance and Dimensions25
- To Prepare for Use26
- Front Panel Overview32
- Rear Panel Overview32
- User Interface36
- Common Operation39
- To Use the Built-In Help System44
- To View the Option Information and the Option Installation45
Chapter 2 To Set the Vertical System47
- To Enable or Disable the Analog Channel48
- To Adjust the Vertical Scale48
- Vertical Expansion49
- To Adjust the Vertical Offset49
- Channel Coupling50
- Bandwidth Limit51
- Probe Ratio51
- Input Impedance52
- Waveform Invert53
- To Set the Probe53
  - Passive Probe54
  - Active Probe54
- Amplitude Unit55
- Channel Delay55
- Offset Cal56
- Channel Label57
Chapter 3 To Set the Horizontal System59
- To Adjust the Horizontal Time Base60
- To Adjust the Horizontal Position60
- Delayed Sweep61
Chapter 4 To Set the Sample System63
- Timebase Mode64
- Acquisition Mode67
- Sampling Mode69
- Sample Rate69
- Memory Depth71
- Anti-Aliasing72
- Horizontal Expansion72
Chapter 5 To Trigger the Oscilloscope75
- Trigger Source76
- Trigger Level77
- Trigger Mode78
- Trigger Coupling79
- Trigger Holdoff79
- Noise Rejection80
- Trigger Type81
- Zone Trigger126
- Trigger Output Connector128
Chapter 6 Operations and Measurements129
- Math Operation130
- Auto Measurement152
- Cursor Measurement164
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter175
- Digital Voltmeter (DVM)176
- Frequency Counter178
Chapter 8 Power Analysis (Option)181
- Power Quality182
- Ripple184
Chapter 9 Histogram Analysis187
- To Enable or Disable the Histogram Function188
- To Select the Histogram Type188
- To Select the Histogram Source189
- To Select the Measurement Item189
- To Set the Histogram Height189
- To Set the Histogram Range189
- To Enable or Disable the Statistical Function190
- To Reset190
Chapter 10 Real-Time Eye Diagram and Jitter Analysis (Option)191
- Real-Time Eye Analysis192
- Jitter Analysis196
Chapter 11 Protocol Decoding201
- Parallel Decoding202
- RS232 Decoding (Option)206
- I2C Decoding (Option)212
- SPI Decoding (Option)216
- LIN Decoding (Option)220
- CAN Decoding (Option)225
- Flexray Decoding (Option)229
- I2S Decoding (Option)233
- 1553B Decoding (Option)236
Chapter 12 Reference Waveform241
- To Enable Ref Function242
- To Select the Reference Channel242
- To Select the Ref Source242
- To Adjust the Ref Waveform Display242
- To Save to Internal Memory243
- To Clear the Display of the Reference Waveform243
- To View Details of the Reference Waveform243
- To Reset the Reference Waveform243
- Color Setting244
- Label Setting244
- To Export to Internal or External Memory244
- To Import from Internal or External Memory245
- Binary Data Format (.Bin)245
  - Binary Header Format245
Chapter 13 Pass/Fail Test249
- To Enable or Disable the Pass/Fail Test Function250
- To Start or Stop the Pass/Fail Test Operation250
- To Select the Source250
- To Create a Mask251
- To Save a Mask251
- To Load a Mask251
- To Set the Output Form of the Test Results252
- To Enable or Disable the Display of the Statistics of the Test Results252
- Statistics Reset253
Chapter 14 Waveform Recording & Playing255
- Common Settings256
- Record Options257
- Play Options258
Chapter 15 Search and Navigation Function259
- Search Function260
- Navigation Function262
Chapter 16 Display Control265
- To Select the Display Type266
- To Set the Persistence Time266
- To Set the Waveform Intensity266
- To Set the Screen Grid267
- To Set the Grid Brightness267
- Scale267
- Color Grade268
- Waveform Freeze268
Chapter 17 Function/Arbitrary Waveform Generator (Option)269
- To Output Basic Waveforms270
- To Output the Arbitrary Waveform276
- Modulation279
  - Fsk282
- Sweep282
- Burst284
Chapter 18 Store and Load287
- Storage System288
- Storage Type288
- Load Type290
- Internal Storage and Load290
- External Storage and Load292
- Disk Management292
- Factory Settings298
Chapter 19 System Utility Function Setting311
- Remote Interface Configuration312
- System-Related318
Chapter 20 Remote Control331
- Remote Control Via USB332
- Remote Control Via LAN336
- Remote Control Via GPIB337
Chapter 21 Troubleshooting339
Chapter 22 Appendix341
- Appendix A: Accessories and Options341
- Appendix B: Warranty343
Index345

Rigol DS8000-R Series

Table of Contents

Other manuals for Rigol DS8000-R Series

Related product manuals