Name: Rigol DS8000-R Series
Brand: Rigol
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Chapter 16 Display Control    RIGOL 
DS8000-R User Guide  16-1 
Chapter 16 Display Control 
 
In the display control setting menu, you can set the parameters such as the 
waveform display type, persistence time, intensity, grid type, grid brightness, and 
etc. 
 
Contents in this chapter: 
◼  To Select the Display Type 
◼  To Set the Persistence Time 
◼  To Set the Waveform Intensity 
◼  To Set the Screen Grid 
◼  To Set the Grid Brightness 
◼  Scale 
◼  Color Grade 
◼  Waveform Freeze 
 
 
 

Safety Requirement4
- Safety Notices and Symbols6
- Measurement Category7
- Ventilation Requirement7
- Working Environment8
- Care and Cleaning9
- Environmental Considerations10
DS8000-R Series Overview11
Document Overview12
- Table of Contents15
Chapter 1 Quick Start23
- General Inspection24
- Appearance and Dimensions25
- To Prepare for Use26
- Front Panel Overview32
- Rear Panel Overview32
- User Interface36
- Common Operation39
- To Use the Built-In Help System44
- To View the Option Information and the Option Installation45
Chapter 2 To Set the Vertical System47
- To Enable or Disable the Analog Channel48
- To Adjust the Vertical Scale48
- Vertical Expansion49
- To Adjust the Vertical Offset49
- Channel Coupling50
- Bandwidth Limit51
- Probe Ratio51
- Input Impedance52
- Waveform Invert53
- To Set the Probe53
  - Passive Probe54
  - Active Probe54
- Amplitude Unit55
- Channel Delay55
- Offset Cal56
- Channel Label57
Chapter 3 To Set the Horizontal System59
- To Adjust the Horizontal Time Base60
- To Adjust the Horizontal Position60
- Delayed Sweep61
Chapter 4 To Set the Sample System63
- Timebase Mode64
- Acquisition Mode67
- Sampling Mode69
- Sample Rate69
- Memory Depth71
- Anti-Aliasing72
- Horizontal Expansion72
Chapter 5 To Trigger the Oscilloscope75
- Trigger Source76
- Trigger Level77
- Trigger Mode78
- Trigger Coupling79
- Trigger Holdoff79
- Noise Rejection80
- Trigger Type81
- Zone Trigger126
- Trigger Output Connector128
Chapter 6 Operations and Measurements129
- Math Operation130
- Auto Measurement152
- Cursor Measurement164
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter175
- Digital Voltmeter (DVM)176
- Frequency Counter178
Chapter 8 Power Analysis (Option)181
- Power Quality182
- Ripple184
Chapter 9 Histogram Analysis187
- To Enable or Disable the Histogram Function188
- To Select the Histogram Type188
- To Select the Histogram Source189
- To Select the Measurement Item189
- To Set the Histogram Height189
- To Set the Histogram Range189
- To Enable or Disable the Statistical Function190
- To Reset190
Chapter 10 Real-Time Eye Diagram and Jitter Analysis (Option)191
- Real-Time Eye Analysis192
- Jitter Analysis196
Chapter 11 Protocol Decoding201
- Parallel Decoding202
- RS232 Decoding (Option)206
- I2C Decoding (Option)212
- SPI Decoding (Option)216
- LIN Decoding (Option)220
- CAN Decoding (Option)225
- Flexray Decoding (Option)229
- I2S Decoding (Option)233
- 1553B Decoding (Option)236
Chapter 12 Reference Waveform241
- To Enable Ref Function242
- To Select the Reference Channel242
- To Select the Ref Source242
- To Adjust the Ref Waveform Display242
- To Save to Internal Memory243
- To Clear the Display of the Reference Waveform243
- To View Details of the Reference Waveform243
- To Reset the Reference Waveform243
- Color Setting244
- Label Setting244
- To Export to Internal or External Memory244
- To Import from Internal or External Memory245
- Binary Data Format (.Bin)245
  - Binary Header Format245
Chapter 13 Pass/Fail Test249
- To Enable or Disable the Pass/Fail Test Function250
- To Start or Stop the Pass/Fail Test Operation250
- To Select the Source250
- To Create a Mask251
- To Save a Mask251
- To Load a Mask251
- To Set the Output Form of the Test Results252
- To Enable or Disable the Display of the Statistics of the Test Results252
- Statistics Reset253
Chapter 14 Waveform Recording & Playing255
- Common Settings256
- Record Options257
- Play Options258
Chapter 15 Search and Navigation Function259
- Search Function260
- Navigation Function262
Chapter 16 Display Control265
- To Select the Display Type266
- To Set the Persistence Time266
- To Set the Waveform Intensity266
- To Set the Screen Grid267
- To Set the Grid Brightness267
- Scale267
- Color Grade268
- Waveform Freeze268
Chapter 17 Function/Arbitrary Waveform Generator (Option)269
- To Output Basic Waveforms270
- To Output the Arbitrary Waveform276
- Modulation279
  - Fsk282
- Sweep282
- Burst284
Chapter 18 Store and Load287
- Storage System288
- Storage Type288
- Load Type290
- Internal Storage and Load290
- External Storage and Load292
- Disk Management292
- Factory Settings298
Chapter 19 System Utility Function Setting311
- Remote Interface Configuration312
- System-Related318
Chapter 20 Remote Control331
- Remote Control Via USB332
- Remote Control Via LAN336
- Remote Control Via GPIB337
Chapter 21 Troubleshooting339
Chapter 22 Appendix341
- Appendix A: Accessories and Options341
- Appendix B: Warranty343
Index345

Rigol DS8000-R Series User Manual

Table of Contents

Other manuals for Rigol DS8000-R Series

Questions and Answers:

Rigol DS8000-R Series Specifications

Related product manuals

Brand	Rigol
Model	DS8000-R Series
Category	Test Equipment
Language	English