Name: Rigol MSO5000-E Series
Brand: Rigol
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Chapter 8 Power Analysis (Option) RIGOL

MSO5000-E User Guide 8-5

the figure below. You can also enable the touch screen to tap the icon at the

right-upper corner of the statistical results window to close it.

⚫ View the Connection Diagram

Press Tips, and then the connection diagram of the ripple analysis is displayed

on the screen. Please connect the cables according to the connection method as

shown in Figure 8-2. Press Tips again or enable the touch screen to tap the icon

at the right-upper corner of the connection diagram window to close it.

Figure 8-2 Connection Diagram of Ripple Analysis

Safety Requirement4
- Safety Notices and Symbols6
- Measurement Category7
- Ventilation Requirement7
- Working Environment8
- Care and Cleaning9
- Environmental Considerations10
MSO5000-E Series Overview11
Document Overview12
- Table of Contents15
Chapter 1 Quick Start23
- General Inspection24
- Appearance and Dimensions25
- To Prepare for Use26
- Front Panel Overview32
- Rear Panel Overview33
- Front Panel Function Overview35
- User Interface41
- Touch Screen Controls44
- Parameter Setting Method48
- To Use the Kensington Security Lock49
- To Use the Built-In Help System50
- To View the Option Information and the Option Installation51
Chapter 2 To Set the Vertical System53
- To Enable or Disable the Analog Channel54
- To Adjust the Vertical Scale55
- Vertical Expansion56
- To Adjust the Vertical Offset56
- Channel Coupling57
- Bandwidth Limit57
- Probe Ratio58
- Input Impedance59
- Waveform Invert59
- Amplitude Unit60
- Channel Delay60
- Offset Cal61
- Channel Label62
Chapter 3 To Set the Horizontal System65
- To Adjust the Horizontal Timebase66
- To Adjust the Horizontal Position67
- Delayed Sweep68
Chapter 4 To Set the Sample System71
- Timebase Mode72
- Acquisition Mode75
- Sampling Mode77
- Sample Rate77
- LA Sample Rate79
- Memory Depth79
- LA Memory Depth80
- Anti-Aliasing80
- Horizontal Expansion81
Chapter 5 To Trigger the Oscilloscope83
- Trigger Source84
- Trigger Level/Threshold Level85
- Trigger Mode86
- Trigger Coupling87
- Trigger Holdoff88
- Noise Rejection89
- Trigger Type90
- Zone Trigger134
- Trigger Output Connector135
Chapter 6 Operations and Measurements137
- Math Operation138
- Auto Measurement163
- Cursor Measurement176
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter187
- Digital Voltmeter (DVM)188
- Frequency Counter190
Chapter 8 Power Analysis (Option)193
- Power Quality194
- Ripple196
Chapter 9 Histogram Analysis199
- To Enable or Disable the Histogram Function200
- To Select the Histogram Type200
- To Select the Histogram Source201
- To Set the Histogram Height201
- To Set the Histogram Range201
- To Enable or Disable the Statistical Function201
- To Reset202
Chapter 10 Digital Channel203
- To Select the Digital Channel204
- To Enable/Disable the Digital Channel204
- To Set the Threshold and Calibrate Probe205
- Auto Arrangement Setting206
- To Set the Waveform Display Size206
- To Set the Label206
- Group Setting207
- Waveform Color of the Digital Channel208
Chapter 11 Protocol Decoding209
- Parallel Decoding210
- RS232 Decoding (Option)215
- I2C Decoding (Option)222
- SPI Decoding (Option)226
- LIN Decoding (Option)231
- CAN Decoding (Option)236
- Flexray Decoding (Option)241
- I2S Decoding (Option)245
- 1553B Decoding (Option)249
Chapter 12 Reference Waveform253
- To Enable Ref Function254
- To Select the Reference Channel254
- To Select the Ref Source254
- To Adjust the Ref Waveform Display254
- To Save to Internal Memory255
- To Clear the Display of the Reference Waveform255
- To View Details of the Reference Waveform255
- To Reset the Reference Waveform256
- Color Setting256
- Label Setting256
- To Export to Internal or External Memory257
- To Import from Internal or External Memory257
Chapter 13 Pass/Fail Test259
- To Enable or Disable the Pass/Fail Test Function260
- To Start or Stop the Pass/Fail Test Operation260
- To Select the Source260
- To Create a Mask261
- To Save the Mask261
- To Load a Mask261
- To Set the Output Form of the Test Results262
- To Enable or Disable the Display of the Statistics of the Test Results263
- Statistics Reset263
Chapter 14 Waveform Recording & Playing265
- Common Settings266
- Record Options267
- Play Options268
Chapter 15 Search and Navigation Function271
- Search Function272
- Navigation Function274
Chapter 16 Display Control277
- To Select the Display Type278
- To Set the Persistence Time278
- To Set the Waveform Intensity279
- To Set the Screen Grid279
- To Set the Grid Brightness279
- Scale280
- Color Grade280
- Waveform Freeze280
Chapter 17 Function/Arbitrary Waveform Generator (Option)281
- To Output Basic Waveforms282
- To Output the Arbitrary Waveform289
- Modulation293
  - Fsk296
- Sweep296
- Burst298
Chapter 18 Store and Load301
- Storage System302
- Storage Type302
- Load Type304
- Internal Storage and Load304
- External Storage and Load306
- Disk Management306
- Factory Settings313
Chapter 19 Bode Plot325
- To Enable the Bode Function326
- To Run or Stop the Operation326
- Parameter Setting327
- Cursor329
- Display Type329
  - Wave Form330
  - Chart330
- Display331
- Save331
- Connection Diagram331
Chapter 20 System Utility Function Setting333
- Remote Interface Configuration334
- System-Related339
Chapter 21 Remote Control353
- Remote Control Via USB354
- Remote Control Via LAN358
- Remote Control Via GPIB359
Chapter 22 Troubleshooting361
Chapter 23 Appendix363
- Appendix A: Accessories and Options363
- Appendix B: Warranty364
Index365

Rigol MSO5000-E Series User Manual

Table of Contents

Other manuals for Rigol MSO5000-E Series

Questions and Answers:

Rigol MSO5000-E Series Specifications

Related product manuals

Brand	Rigol
Model	MSO5000-E Series
Category	Test Equipment
Language	English