Roland FR-8X - Restore Data; Export; Import

Menu Options
110
15.6 Restore Data
This function allows you to undo all or some
changes you made after last saving your settings
by reloading the last version you saved. This can
be handy when it turns out that your changes
don’t yield the expected result and that starting all
over again would be quicker than changing the
parameters back.
NOTE
This function does not necessarily load the factory settings: it
loads the settings stored in the selected memory area(s).
1. Use the [DATA/ENTER] knob to select the type of
parameters you desire to reload.
TYPE Explanation
ALL, Restores all of the FR-8x settings.
Master Tune,
Restores the last “1.1 Master Tune” setting you saved ( p.
71).
Scale Tune,
Restores the last “1.3 Scale Tune” (p. 71) settings you
saved.
System, Restores the last “14. System” settings you saved ( p. 100).
MIDI,
Restores the last “16. MIDI Parameters” settings you
saved ( p. 112).
All Sets
Restores the settings of all Sets and the registers they
contain.
Set 1~100 Restores the settings of the selected Set.
2. Press the [MENU/WRITE] button to reload the settings.
The display conrms this operation.
15.7 EXPORT
This function allows you to save the SET or User
Program data to the connected USB memory.
Parameter Value Explanation
Type
SET, User
Program
Select the type of data you want export.
SET File ALL, Single
Select “ALL” to export All SET.
Select “Single” to export the single SET.
MEMO
This eld is active only if you
selected to export “SET”.
Select SET 1~100
Select the SET you want to export.
MEMO
This eld is active only if you
selected to export a single SET.
User Prog. File
ALL, Bank,
Single, List
Select “ALL” to export All User Program.
Select “Bank” to export all User Program
of the selected bank.
Select “Single” to export the single User
Program.
Select “List” to export the single User
Program List.
MEMO
This eld is active only if you
selected to export “User Program”.
Parameter Value Explanation
User Prog. Bank 1~100
Select the Bank of User Program you
want to export.
MEMO
This eld is active only if you
selected to export a bank of User
Program.
User Prog. Num 1~14
Select the number of User Program you
want to export.
MEMO
This eld is active only if you
selected to export a single User
Program.
See “Export and Import Sets to/from the Optional USB memory” (p.
44).
See “Export User Programs to the Optional USB memory” (p. 64).
15.8 IMPORT
This function allows you to import the settings of
a SET and User Program le. You can choose the
Set and User Program memory the settings should
be loaded to. Moreover you can import FR-7x SET.
Parameter Value Explanation
Type
SET, User
Program,
FR-7x All
SETs, FR-7x
Single SET
Select the type of data you want import.
SET File ALL, Single
Select “ALL” to import All SET.
Select “Single” to import the single SET.
MEMO
This eld is active only if you selected
to import “SET”.
Dest. SET 1~100
Select the SET you want to import.
MEMO
This eld is active only if you selected
to import a single SET.
User Prog. File
ALL, Bank,
Single
Select “ALL” to import All User Program.
Select “Bank” to import all User Program
of the selected bank.
Select “Single” to import a single User
Program.
MEMO
This eld is active only if you selected
to import “User Program”.
UPG Dest. Bank 1~100
Select the Bank of User Program in
which you want to import data.
MEMO
This eld is active only if you selected
to import a bank of User Program.
UPG Dest. Num 1~14
Select the number of User Program you
want to import.
MEMO
This eld is active only if you selected
to import a single User Program.
See “Export and Import Sets to/from the Optional USB memory” (p.
44).
See “Import User Programs to the Optional USB memory” (p. 66).
See “Import FR-7x Sets from the Optional USB memory” (p. 45).