204
MIDI Implementation
❍Foot control (Controller number 4)
Status 2nd byte 3rd byte
BnH 04H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC is set to
“FOOT”.
❍Data Entry (Controller number 6)
Status 2nd byte 3rd byte
BnH 06H mmH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm = The value of the parameter specified by RPN.
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected or adjust [PATTERN]-[PART]-[SETUP]-[PAGE 2]
BEND RANGE setting, the pitch bend sensitivity of the sequencer pattern data will be
transmitted.
Values for the RPN parameter, on the normal mode of TD-8, are as follows.
RPN Data entry
MSB LSB MSB LSB Explanation
00H 00H mmH --- Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
7FH 7FH --- --- RPN null
set condition where RPN is unspecified.
❍Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Volume: 00H - 7FH (0 - 127)
* Only the channel assigned to the percussion part and the backing part are sent.
* When a pattern or a song are selected, the part level of the sequencer pattern data will be
transmitted.
❍Pan (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = pan: 00H - 40H - 7FH (Left - Center - Right)
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected, the pan of the sequencer pattern data will be
transmitted.
❍General purpose controller 1 (Controller number 16)
Status 2nd byte 3rd byte
BnH 10H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or
ZONE CC are set to “GEN1”.
❍General purpose controller 2 (Controller number 17)
Status 2nd byte 3rd byte
BnH 11H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127)
* This is transmitted only on the channel which is assigned to the drum kit part.
* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or
ZONE CC are set to “GEN2”.
❍Hold 1 (Controller number 64)
Status 2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF 64-127 = ON
* Only the channel assigned to the backing part are sent.
* Transmitted only when the TD-8 is in play for Pattern in which Hold 1 is recorded.
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Reverb send level: 00H - 7FHÅi0 - 127Åj
* Only the channel assigned to the percussion part and backing part are sent.
* When a pattern or a song are selected, the reverb send level of the sequencer pattern data
will be transmitted.
❍RPN MSB/LSB (Controller number 101,100)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm = upper byte of parameter number specified by RPN (MSB)
ll = lower byte of parameter number specified by RPN (LSB)
* Only the channel assigned to the backing part are sent.
* When a pattern or a song are selected, the pitch bend sensitivity of the sequencer pattern
data will be transmitted.
* Regarding the RPN please refer to p. 201.
Values for the RPN parameter, on the normal mode of TD-8, are as follows. Regarding the
value of each parameter, refer to Data Entry (Controller number 6).
RPN
MSB LSB
Parameter
00H 00H Pitch Bend Sensitivity
7FH 7FH RPN null
● Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* Not transmitted when [SETUP]-[MIDI]-[PROG] PROGRAM CHANGE RX SW is set to
“OFF”.(Initial Value is ON)
* Program changes corresponding to drum kit are sent when drum kits are selected.
* Program changes corresponding to each part’s instrument are sent when songs or
patterns are selected. Also, when instruments are selected for parts, program changes for
the respective instruments are sent.
● Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Only the channel assigned to the backing part are sent.
* Transmitted only when the TD-8 is in play for pattern in which pitch bend change is
recorded.
■ System Realtime Message
● Timing Clock
Status
F8H
● Start
Status
FAH
To Next Page
Loading...
