Saab R60 - Page 60

To Next Page

To Previous Page

R60 Station

R60 User Manual

Document Number

Version

Date

7000 120-019

2022-08-10

Page 60 (98)

Note: When DSC is used for transmitting channel management zones, then the

base station will be unable to receive anything on the AIS channels during

DSC transmissions.

Main Page

Table of Contents5
Introduction10
Document Orientation10
References11
Front Panel13
Power Button13
Operation13
LED Indications13
Front Display13
Introduction13
Main Menu14
Figure 2-1: Front Display Main Menu14
Status15
Statistics16
Alarms17
Figure 2-2: Statistics View17
Base Station, Aton and Receiving Station18
Vdl18
Figure 2-3: R60 Station Status View18
Settings19
Table 2-1 - Front Display Configuration Parameters19
Getting Started20
R60 Station Variants and Licenses20
Installation and Compatibility20
Connecting to the R60 Web Interface21
Connecting to the R60 Supervisor21
Introduction to the R60 Web Interface22
Figure 3-1: Web GUI Start Page, Showing the Four Main Categories23
Figure 3-2: How to Come Back to the Web Gui Start Page23
Navigating the Web Interface24
Figure 3-3: the Navigator Line Shows Selected Category and if Applicable also Sub-Category24
Figure 3-4: Shortcuts to the Top Level of the Present Main Category, or Directly to the Top Level of Another Main Category25
Figure 3-5: Shortcuts to Top Level of the Present Sub-Category, or Directly to Other Sub-Categories25
Visual Appearance of the Web Interface26
Saving Parameter Changes in the Web Interface26
Introduction to Main Categories26
Figure 3-6: Make Sure to Use the Figure 3-7: Top Menu of the Configure Category26
HW/SW Info27
Monitor27
Configure27
Maintenance27
Quick Introduction to Set-Up of a New R60 Station28
General Set-Up Procedure28
Figure 3-8: General, Sub-Page of the Configure Category30
Figure 3-9: Changing from the General Sub Category Directly to the Gnss Sub Category31
Figure 3-10: Gnss Sub Category31
Figure 3-11: Reporting Rates Page (Applies for Base Stations Only)33
Figure 3-12: Data Link Management Page34
Figure 3-13: Network Page35
Set-Up Procedure for a Redundant Configuration36
Figure 3-14: Hot Standby Category Page36
Hw/Sw Info38
Introduction38
License Info38
Version Functionality38
Unavailable Functions39
Update License39
Table 4-1 - Licensed Features in the Table 5-1 - Description of Features Monitored in the39
Monitor40
Introduction40
Monitor > Alarms40
Monitor > Status41
Table 5-2 - Description of Alarm Indicator Icons41
Monitor > Position Reports42
Table 5-3 - Featured Display of the Table 6: Vdl Link Map Information Panel Fields42
Figure 5-1: Monitoring Position Reports Page43
Monitor > Data Log44
Log Panel44
Clipboard Panel44
Monitor > Vdl Link Map45
R60 User Manual45
Information Panel45
Figure 5-2: Monitoring Data Log Page45
Legend Panel46
Channels Panel46
Freeze/Unfreeze Button46
Channel Grid Panels46
Figure 5-3: Monitoring Vdl Link Map Page47
Configure48
Introduction48
Editing and Storing Changes48
Figure 6-1: Password Is Required to Enter the Configure Category48
Configure > General49
Table 6-1 - General Parameters50
Configure > Network51
Table 6-2 - Network Parameters52
Configure > Interfaces53
Table 6-3 - Parameters for Interfaces53
Configure > Gnss54
Position54
Dgnss54
Self-Surveyed Position55
Viewing Self-Surveyed Position55
GNSS Parameters55
Table 6-4 - Parameters on the Gnss56
Configure > Reporting Rates (Base Station Only)57
Configure > Data Link Management (Base Station Only)57
Table 6-5 - Parameters for Reporting57
Table 6-6 - Parameters for Data Link58
Configure > Channel Management (Base Station Only)59
Table 6-7 - Parameters for Channel59
Configure > Group Assignment (Base Station Only)61
Table 6-8 - Parameters for Groupa62
Onfigure > Vsi & Fsr Sentences63
Table 6-9 - Parameters for Vsi/Fsr64
Configure > Third AIS Channel (Full Base Station Only)65
Table 6-10 - Parameters for Third65
Configure > Hot Standby66
Figure 6-2: R60 in a Redundant Pair Configuration66
Table 6-11 - Parameters for the Hot68
Configure > Repeater (Full Base Station Only)69
Process Used to Repeat a Message69
Configure > Repeater > General70
Configure > Repeater > Reservations71
Table 6-12 - Parameters for Ther71
Configure > Repeater > MMSI Filter72
Table 6-13 - Parameters for Ther72
Configure > Repeater > Area Filter73
Table 6-14 - Parameters for Ther73
Table 6-15 - Parameters for Ther75
Configure > Aids to Navigation (Aton Station and Full Base Station)76
Table 6-16 - Parameters for Thea77
Configure > Aton Message Repeater (Aton Station and Full Base Station)78
Table 6-17 - Parameters for the Ato78
Configure > Special Aids to Navigation Functions79
Table 6-18 - Parameters for Thes80
Configure > VDL Status/Reboot81
Table 6-19 - Parameters for Vdl S81
Table 6-20 - R60 Status Information Messages82
Configure > Password83
Table 6-21 - Password Parameters83
Maintenance84
Configuration84
Restart R60 Station84
Upgrade Firmware/Software84
Snmp Mib85
Supervisor Web86
Figure 8-1: Supervisor Info86
Table 8-1 Parameter Information Provided Via87
Snmp Monitoring88
Nmea Sentences89
Channel Management89
Multiple Group Assignment Areas89
Data Link Messages89
DGNSS Message 1790
Technical Data91
Declarations, Approvals and Certificates93
R60 User Manual93
Ais Base Station Statement of Conformity93
Moduleb Certificate95
REACH and Rohs Declaration96
Acronyms97

Saab R60 - Page 60

Table of Contents