: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 21
Operation/Procedure
1) Select the number corresponding to the target of operation check
with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
The operating conditions of the sensors and detectors are displayed.
The active sensors and detectors are highlighted.
2-3
Purpose Operation test/Check
Function
(Purpose)
Used to check the operations of the loads in the
automatic document feeder unit and the control
circuits.
Section DSPF
Item Operation
1 MOTOR (T) Motor top speed
2 MOTOR (H) Motor high speed
3 MOTOR (L) Motor low speed
4 STRBC Document transport brake clutch
5 STRC Document feed transport clutch
6 SPFC Document fed clutch
7 SRRC Document resist clutch
8 SRRBC Document resist brake clutch
9 STRRC Document feed resist clutch
10 STRRBC Document feed resist brake clutch
11 STMPS Stamp solenoid
12 SLUM Lift up motor
13 SPFFAN SPF fan motor
Press [START] key, and the
operation is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
SIMULATION 2-2
SPF SENSOR CHECK.
SSET SOCD SCOV SPED2
SPED1 SPPD1 SPPD2 SPPD3
SPPD4 SPOD SWD6 SWD5
SWD4 SWD3 SWD2 SWD1
SPLS2 SPLS1 CISSET STSET
STUD STLD
SWD_LEN: 2100 SWD_AD: 600
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-13, AND PRESS START.
1.MOTOR(T) 2.MOTOR(H) 3.MOTOR(L)
4.STRBC 5.STRC 6.SPFC 7.SRRC
8.SRRBC 9.STRRC 10.STRRBC 11.STMPS
12.SLUM 13.SPFFAN
2
SIMULATION 2-3
SPF LOAD TEST. EXECUTING···.
1.MOTOR(T) 2.MOTOR(H) 3.MOTOR(L)
4.STRBC 5.STRC 6.SPFC 7.SRRC
8.SRRBC 9.STRRC 10.STRRBC 11.STMPS
12.SLUM 13.SPFFAN
2
3
3-2
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of sensor and detector in
the finisher and the related circuit.
Section Finisher
Item Operation
PI1 Entry port paper detection
PI1P Punch width resist HP detection When the punch unit is
installed
PI1S Paper holding plate motor clock
detection
When the saddle unit is
installed
PI2P Punch motor clock detection When the punch unit is
installed
PI2S Front door open detection When the saddle unit is
installed
PI3 Paper exit detection
PI3P Punch HP detection When the punch unit is
installed
PI3S Paper exit cover open detection When the saddle unit is
installed
PI4S Paper folding motor clock
detection
When the saddle unit is
installed
PI5 Shutter open detection
PI5S Alignment plate HP detection When the saddle unit is
installed
PI6 Alignment guide HP detection
PI6S Saddle tray paper detection When the saddle unit is
installed
PI7 Staple shift HP detection
PI7S Paper positioning plate HP
detection
When the saddle unit is
installed
PI8 Tray 1 HP detection
PI8S Paper positioning plate HP
detection
When the saddle unit is
installed
PI9 Tray 1 lift motor clock detection 1
PI9S Entry port cover open detection When the saddle unit is
installed
PI10 Paper exit motor clock detection
PI11 Tray 1 paper detection
PI11S Saddle paper exit detection When the saddle unit is
installed
PI12 Tray 2 paper detection
PI12S Semi-circular roller phase
detection
When the saddle unit is
installed
PI13S Guide HP detection When the saddle unit is
installed
PI14 Buffer path detection
PI14S Paper holding plate lead edge
position detection
When the saddle unit is
installed
PI15 Finisher joint detection
PI15S Paper holding plate lead edge
position detection
When the saddle unit is
installed
PI16 Door open detection
PI17 Buffer path entry port paper
detection
PI17S Vertical path paper detection When the saddle unit is
installed
PI18 Oscillating guide open detection
PI18S Saddle No. 1 paper detection When the saddle unit is
installed
To Next Page
Loading...
