: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 34
Operation/Procedure
1)The ROM version of each section can be checked. When there is
any problem in the software, use this simulation to check the ROM ver-
sion of each section and revise the version if necessary.
Operation/Procedure
When installing or servicing this machine, execute this simulation to
print and save various setting and adjustment data for next servicing.
(For example, memory trouble, PWB replacement, etc.)
1) Enter 1 with 10-key.
2) Press [START] key.
The various setting and adjustment data are printed out. (The print
paper cannot be selected optionally.)
Operation/Procedure
The key operator code is displayed.
Operation/Procedure
The values of the finisher counter, the scanner (read), counter, and the
SPF related counters are displayed.
Operation/Procedure
The values of the paper feed related counters are displayed.
22-5
Purpose Other
Function
(Purpose)
Used to check the ROM version of each unit (section).
Section
Item Software
S/N Engine section serial number
MFP MFP controller
(LANGUAGE) (Language version)
BOOT MFP controller BOOT ROM
FAX FAX controller
PCU PCU controller
SCANNER Scanner controller
FINISHER Finisher controller
SADDLE UNIT Saddle unit
LCC Side LCC
INSERTER Inserter
22-6
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to output the list of the setting and adjustment
data (simulations, FAX soft switch, counters).
Section
Item Data Adjust/Setting data
0 TRAY SELECT TRAY SELECT auto only (Selection is not
allowed.)
1 PRINT START PRINT START
Select 1 and press
[START] key.
Press [CUSTOMSETTING] key or [START]
key.
SIMULATION 22-5
ROM VERSION DATA DISPLAY.
S/N: 0000000000
MFP: 1.00 (LANGUAGE: 1.00)
PCU: 1.00 BOOT: 1.00
SCANNER: 1.00 FAX: 1.00
FINISHER: 1.00
SADDLE UNIT: 1.00 LCC: 1.00
INSERTER: 1.00
SIMULATION 22-6
DATA PRINT MODE. SELECT SETTING, AND PRESS START.
0. TRAY SELECT :AUTO ONLY
1. PRINT START
1
SIMULATION 22-6
0
DATA PRINT MODE. EXECUTING···.
0. TRAY SELECT :1
22-7
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to display the key operator code. (This simulation
is used when the customer forgets the key operator
code.)
Section
Item Data User data
22-8
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check the number of use of the finisher, the
SPF, and the scan (reading) unit.
Section Optical (Image scanning) Finisher
Item Counter
SPF Document feed quantity
SCAN Number of scans
STAPLER Number of stapling
PUNCH Number of punching
STAMP Number of SPF finish stamps
SADDLE STAPLER Number of saddle staples
INSERTER Number of inserter operations
22-9
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check the number of use (print quantity) of
each paper feed section.
Section Paper feed, ADU
Item Counter
TRAY1 Tray 1 use quantity
TRAY2 Tray 2 use quantity
TRAY3 Tray 3 use quantity
TRAY4 Tray 4 use quantity
BPT Manual feed tray use quantity
ADU Duplex paper feed quantity
LCC Side LCC use quantity
SIMULATION 22-7
KEY OPERATOR CODE DISPLAY.
CODE: *****
SIMULATION 22-8
ORG./STAPLE COUNTER DATA DISPLAY.
SPF: ********
SCAN: ********
STAPLER: ******** PUNCH: ********
STAMP: ******** SADDLE STAPLER: ********
INSERTER: ******** INSERTER OFF LINE: ********
SIMULATION 22-9
PAPER FEED COUNTER DATA DISPLAY.
TRAY1: ******** TRAY2:********
TRAY3: ******** TRAY4:********
BPT: ******** ADU: ********
LCC: ********
To Next Page
Loading...
