: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 45
Operation/Procedure
The operating conditions of sensors and detectors are displayed.
The active sensors and detectors are highlighted.
Operation/Procedure
The operating conditions of sensors and detectors are displayed.
The active sensors and detectors are highlighted.
The paper width size detection level is displayed.
Operation/Procedure
1) Open the manual paper feed guide to the max. width.
2) Select MAX POSITION with 10-key.
3) Press [START] key.
The max. width detection level is recognized.
4) Press [CUSTOM SETTINGS] key.
5) Set the manual paper feed guide to A4R size width.
6) Select POSITION with 10-key.
7) Press [START] key.
The A4R width detection level is recognized.
8) Press [CUSTOM SETTINGS] key.
10) Select POSITION2 with 10-key.
11) Press [START] key.
12) Press [CUSTOM SETTINGS] key.
13) Open the manual paper feed guide to the min. width.
14) Select MIN POSITION with 10-key.
15) Press [START] key.
The min. width detection level is recognized.
If the above procedures are not completed normally, "ERROR" is dis-
played. If completed normally, "COMPLETE" is displayed.
30-2
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of sensors and detectors
in the paper feed section and the related circuits.
Section Paper feed
Item Operation
TANSET
Tray 1 and 2 insertion detection
TLUD1
Tray 1 upper limit sensor
TSPD1
Tray 1 remaining quantity sensor
TPED1
Tray 1 paper sensor
TLUD2
Tray 2 upper limit sensor
TSPD2
Tray 2 remaining quantity sensor
TPED2
Tray 2 paper sensor
MPLD1 Manual feed length detection 1
MPLD2 Manual feed length detection 2
MTOP1 Manual pull-out sensor 1
MTOP2 Manual pull-out sensor 2
MPED Manual feed paper empty detection 2
MPFD1 Detection 1 of paper pass from manual paper feed
MPFD2 Detection 2 of paper pass from manual paper feed
MPRD1 Manual relay paper detection 1
MPRD2 Manual relay paper detection 2
Bypass Tray size: (The manual feed tray detection size is displayed.)
M1PFD
Tray 3 transport detection
M1LUD
Tray 3 upper limit detection
M1PED
Tray 3 paper empty detection
M1SS1
Tray 3 rear edge switch 1
M1SS2
Tray 3 rear edge switch 2
M1SS3
Tray 3 rear edge switch 3
M1SS4
Tray 3 rear edge switch 4
M1SPD
Tray 3 paper remaining quantity detection
Tray 3 size: (The tray 3 detection size is displayed.)
M2PFD
Tray 4 transport detection
M2LUD
Tray 4 upper limit detection
M2PED
Tray 4 paper empty detection
M2SS1
Tray 4 rear edge switch 1
M2SS2
Tray 4 rear edge switch 2
M2SS3
Tray 4 rear edge switch 3
M2SS4
Tray 4 rear edge switch 4
M2SPD
Tray 4 paper remaining quantity detection
Tray 4 size: (The tray 4 detection size is displayed.)
1
1
1
SIMULATION 30-2
TRAY SENSOR CHECK..
TANSET TLUD1 TSPD1 TPED1 TLUD2 TSPD2 TPED2
MPLD1 MPLD2 MTOP1 MTOP2 MPED MPFD1 MPFD2
MPRD1 MPRD2
(Bypass Tray size: A3)
M1PFD M1LUD M1PED M1SS M1SS2 M1SS3 M1SS4
M1SPD
(Tray3 size: A3)
M2PFD M2LUD M2PED M2SS M2SS2 M2SS3 M2SS4
M2SPD
(Tray4 size: A3)
40
40-1
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the manual feed tray
paper size detector and the related circuit. (The
operation of the manual feed tray paper size detector
can be monitored with the LCD display.)
Section Paper feed
Item Operation
MPLD1 Manual tray length detection 1
MPLD2 Manual tray length detection 2
MTOP1 Manual tray pull-out detection 1
MTOP2 Manual tray pull-out detection 2
BYPASS_WIDTH Manual feed guide plate position
BYPASS_AD Manual feed width detection volume output AD
value
Bypass Tray width
size
(Manual tray detection size is displayed.)
A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R, A5R,
5.5x, 7.25x, EXTRA
40-2
Purpose Adjustment
Function
(Purpose)
Used to adjust the manual paper feed tray paper width
detector detection level.
Section Paper feed
Item Operation
9) Set the manual paper feed guide to A5/A5R size width.
The A5/A5R width detection level is recognized.
SIMULATION 40-1
BYPASS TRAY SENSOR CHECK..
MPLD1 MPLD2 MTOP1 MTOP2
BYPASS_WIDTH: 2100 BYPASS_AD: 600
(Bypass Tray width size: A4/A3)
1
1
To Next Page
Loading...
