AR-M550/M620/M700 SIMULATION 8 - 59
Operation/Procedure
(Copy mode selection)
1) Select the number corresponding to the copy mode to be adjusted
with 10-key. (Select one of 3 - 14.)
2) Press [START] key.
(Print mode selection in the FAX mode)
1) Enter 2 with 10-key.
2) Press [START] key.
3) Select the number corresponding to one of the following adjust-
ment items. (Select one of 3 - 14.)
∗ Normal mode (Print density adjustment level)
∗ Normal mode (Print density adjustment level) (Half-tone mode)
∗ Auto mode
∗ Auto mode (Half-tone mode)
Exposure level
4) Press [START] key.
(Gamma adjustment)
After completion of the above procedures, perform the following proce-
dures.
1) Enter the gamma level with 10-key.
2) Enter [P] key or [CUSTOM SETTINGS] key.
When [START] key is pressed, printing is performed and the
adjustment value is set simultaneously.
Check the gamma density (copy density in the low density area
and the high density area) of printed copy image. The greater the
adjustment value is, the greater the gamma value is, resulting in a
higher contrast.
(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value in
this simulation, the adjustment value is set. When START key
is pressed, the adjustment value is set and copying is per-
formed.
Press [START] key. Press [CUSTOM SETTINGS] key.
46-18
Purpose Adjustment
Function
(Purpose)
Used to adjust the gamma (density gradient) in the
copy mode.
Section
Item Picture quality Density
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3 OC_AE AE mode (OC) 0 - 127 64
4 OC_CHARA Text mode (OC)
5 OC_MIX Text/Photo mode (OC)
6 OC_PHOTO Photo mode (OC)
7 SPF_AE AE mode (SPF)
8 SPF_CHARA Text mode (SPF)
9 SPF_MIX Text/Photo mode (SPF)
10 SPF_PHOTO Photo mode (SPF)
11 CIS_AE AE mode (CIS)
12 CIS_CHARA Text mode (CIS)
13 CIS_MIX Text/Photo mode (CIS)
14 CIS_PHOTO Photo mode (CIS)
SIMULATION 46-17
CCD/CIS SHADING GAIN DATA SETUP. SELECT 1-5, AND
PRESS START.
1. CCD FRONT ODD 128 2. CCD FRONT EVEN 128
3. CCD REAR ODD 128 4. CCD REAR EVEN 128
5. CIS 128
128
SIMULATION 46-17
CCD SHADING GAIN DATA SETUP. INPUT VALUE 0-255,AND
PRESS START.
1.CCD ODD
1
Item
3AUTO Auto
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
9 AUTO (H) Auto (Half-tone)
10 1.0 (H) Exposure level 1 (Half-tone)
11 2.0 (H) Exposure level 2 (Half-tone)
12 3.0 (H) Exposure level 3 (Half-tone)
13 4.0 (H) Exposure level 4 (Half-tone)
14 5.0 (H) Exposure level 5 (Half-tone)
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
To Next Page
Loading...
