AR-M550/M620/M700 SIMULATION 8 - 60
Operation/Procedure
(Toner save operation YES/NO setting in the auto mode)
1) Select "1. AE MODE" with 1-key.
2) Press [START] key.
3) Select the number corresponding to the operation specifications
with 10-key.
4) Press [START] key.
When [START] key is pressed, the adjustment value is set.
(Operation setting in the auto copy mode)
1) Select the number corresponding to the mode with 10-key. (Select
one of 2 - 4.)
2) Press [START] key.
3) Select the number corresponding to the operation mode with 10-
key.
4) Press [START] key.
Operation/Procedure
(Adjustment mode selection)
1) Select the number corresponding to the copy mode to be adjusted
with 10-key.
SPF front frame side (Front surface copy), SPF rear frame side
(Front surface copy), SPF (Back surface copy) (Select one of 3 -
5.)
2) Press [SATART] key.
(Copy density level adjustment)
1) Enter the density correction value with 10-key.
2) Press [P] key or [START] key.
Select 2, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
46-19
Purpose Adjustment
Function
(Purpose)
Used to set the auto mode operation specifications in
each mode (copy, scan, FAX).
Section
Item Picture quality Density
64
1
SIMULATION 46-18
GAMMA SETUP(COPIER). SELECT 1-14, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1
3.OC_AE 64 4.OC_CHARA 5.OC_MIX 64
6.OC_PHOTO 64 7.SPF_AE 64 8.SPF_CHARA 64
9.SPF_MIX 64 10.SPF_PHOTO 64 11.CIS_AE 64
12.CIS_CHARA 64 13.CIS_MIX 64 14.CIS_PHOTO 64
SIMULATION 46-18
GAMMA SETUP. INPUT VALUE 0-127, AND PRESS START.
3.OC_AE
SIMULATION 46-18
GAMMA SETUP. NOW PRINTING.
SIMULATION 46-18
GAMMA SETUP. SELECT 1-6, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select other than 0 - 2,
and press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
Select 1,
and press
[START] key.
Select 0, and press [START] key.
1
SIMULATION 46-18
EXP.LEVEL SETUP FAX(SUPER FINE). SELECT 3-14, AND PRESS
START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
9.AUTO(H) 10.1.0(H) 11.2.0(H)
12.3.0(H) 13.4.0(H) 14.5.0(H)
1 AE MODE AE mode
2 AE STOP MODE (COPIER) AE fixed mode (Copier)
3 AE STOP MODE (SCANNER) AE fixed mode (Scanner)
4 AE STOP MODE (FAX) AE fixed mode (FAX)
Mode
Set
value
Item Default
AE
mode
1 Image quality priority mode (Normal
mode)
∗ Gamma is sharp to provide high
contrast images.
1 (Japan)
2 (EX Japan)
2 Toner consumption priority mode
∗ Gamma is mild to provide low
contrast images.
AE
fixed
mode
0 AE fixed OFF 1 (COPIER)
0 (SCANNER/
FAX)
1 AE fixed ON
AE fixed OFF: The automatic density (exposure) control is performed
in real time. (The density level is changed in real time
according to the document pattern.)
AE fixed ON: The density at the lead edge of the document is
scanned, and the overall density (exposure) level is
determined according to the scanned density level.
(Overall density level fixed)
Select 2, 3, or 4 and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
46-20
Purpose Adjustment
Function
(Purpose)
Used to adjust the copy density correction in the SPF
copy mode for the document table copy mode. The
adjustment is made so that the copy density becomes
the same as that of the document table copy mode.
Section SPF
Item Picture quality Density
2
Select 1, and
press [START] key.
Press [CUSTOM SETTINGS] key.
SIMULATION 46-19
EXP.MODE SETUP. SELECT 1-4, AND PRESS START.
1.AE MODE 2
2.AE STOP MODE(COPIER) 1
3.AE STOP MODE(SCANNER)0
4.AE STOP MODE(FAX) 0
SIMULATION 46-19
EXP.MODE SETUP. INPUT VALUE 1-2, AND PRESS START.
1.AE MODE
1
SIMULATION 46-19
EXP.MODE SETUP. INPUT VALUE 0-1, AND PRESS START.
2.AE STOP MODE(COPIER)
To Next Page
Loading...
