AR-M550/M620/M700 SIMULATION 8 - 70
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
Operation/Procedure
(Lead edge image loss adjustment)
1) Set the front and back surface image loss adjustment values
(LEAD EDGE) as specified below:
(Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5)
Paper lead edge void: 3.5mm (DENA: 35)
∗ Set the adjustment value of LEAD to 15. (Enter 15 as the adjust-
ment value of LEAD EDGE, and press [P] key.)
2) Set the adjustment value of L4 to 0. (Enter 0 as the adjustment
value of L4, and press [P] key.
3) Set the adjustment value of L5 to 0. (Enter 0 as the adjustment
value of L5, and press [P] key.
4) Make a copy at 200% with the SPF, and calculate the values of L4
and L5. (Enter 200 as the set value of the copy magnification ratio
set value (MAGNIFICATION) and press [START] key.)
Set range 25 - 200 (%)
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection 1 - 6 –
1 COPY START Copy START (Default) ––
2 MAGNIFICATION Print magnification ratio 25 -
200%
–
(Lead edge adjustment value)
3 SIDE1 Front surface document
scan start position
adjustment value
0 - 99 50
4 SIDE2 Back surface document
scan start position
adjustment value
(Image loss set value: SIDE 1)
5 LEAD_EDGE Front surface lead edge
image loss set value
0 - 99 15
6 FRONT_REAR Front surface side edge
image loss set value
20
7 TRAIL_EDGE Front surface rear edge
image loss set value
0 - 20 0
(Image loss set value: SIDE 2)
8 LEAD_EDGE Back surface lead edge
image loss set value
0 - 99 15
9 FRONT/REAR Back surface side edge
image loss set value
20
10 TRAIL_EDGE Back surface rear edge
image loss set value
0 - 20 0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
Select 2, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
50-7
Purpose Adjustment
Function
(Purpose)
Used to adjust the copy image position and void area
(image loss) on print paper in the copy mode. (The
similar adjustment can be performed with SIM 50-6.)
(SPF mode)
Section
Item Picture quality
L4 = Distance (mm) from the image lead edge position to the
scale of 10mm x 10
50
1
2
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA)3.SIDE1 50 4.SIDE2 50
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0
SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS
START.
3.SIDE1
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Select 1,
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-6
LEAD EDGE ADJUSTMENT(SPF).
(MAGNIFICATION)
INPUT 25-200(%)
To Next Page
Loading...
