Sharp AR-M550N - Page 329

AR-M550/M620/M700 SIMULATION 8 - 71
5) Enter the above values as the set values of L4 and L5. (Enter the
adjustment values of L4 and L5, and press [P] key.)
(The image scan start timing is determined with the detection tim-
ing of the document lead edge by the detector SPPD4.)
If the adjustment result is not satisfactory, perform the above proce-
dures again or adjust with SIM 50-1.
NOTE: If the adjustment result of the above procedures is not satisfac-
tory, though the adjustment value is changed individually, the
adjustment cannot be completed normally.
Repeat procedures 2) - 6) until a satisfactory result is obtained.
(Rear edge image loss adjustment)
Adjust so that the rear edge image loss is 3.5mm. (Change the adjust-
ment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment
value of SIDE, and press [P] key.)
When the adjustment value is changed, the image position is shifted in
the front/rear frame direction.
NOTE: When [P] key is pressed after entering the adjustment value,
the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is performed.
(Table 2)
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
∗ To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
(Table 1)
(Table 2)
(Table 3)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex mode (DD), and a duplex copy is made.
L5 = Distance (mm) from the image lead edge position to the
paper lead edge x 10
Set range 25 - 200 (%)
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
(1 - 6)
––
1 COPY START Copy START (Default) ––
2 MAGNIFICATION Print magnification ratio
(25 - 200%)
––
(Lead edge adjustment value)
3 L4 Distance from the front
surface image lead edge
to the scale of 10mm
(SPF: 200%)
0 - 999 –
4 L5 Distance from the back
surface image lead edge
to the scale of 10mm
(SPF: 200%)
–
(Image loss set value: SIDE 1)
5 LEAD_EDGE Front surface lead edge
image loss set value
0 - 99 15
6 FRONT_REAR Front surface side edge
image loss set value
20
7 TRAIL_EDGE Front surface rear edge
image loss set value
0 - 20 0
(Image loss set value: SIDE 2)
8 LEAD_EDGE Back surface lead edge
image loss set value
0 - 99 15
9 FRONT/REAR Back surface side edge
image loss set value
20
10 TRAIL_EDGE Back surface rear edge
image loss set value
0 - 20 0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
Select 2, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
50
1
2
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 200
(ADJUSTMENT DATA) 3.L4 160 4.L5 160
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0
SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0
Press [CUSTOM SETTING] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
PRESS START.
3.L4
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select 1,
and press
[START] key.
Select 0, and press [START] key.
Select other than 0 - 2, and press [START] key.
100
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)