AR-M550/M620/M700 SIMULATION 8 - 72
Operation/Procedure
(Print image off-center position adjustment)
NOTE: This simulation cannot provide an accurate adjustment. Do not
use.
1) Enter the number corresponding to the number of the paper feed
tray to be adjusted with 10-key. (Select one of 3 - 9.)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed, the
adjustment value set and copying is performed.
(Image off-center adjustment)
1) Enter 1 with 10-key.
2) Press [START] key. The adjustment pattern is printed.
3) Check the off-center of the printed image.
(UNIT: 0.1mm/step When the adjustment value is increased, the
print image is shifted to the front direction.)
NOTE: This adjustment can be performed with SIM 50-5.
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key. (Select one of 1 - 6)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value and 10 is entered, the mode is
changed to the duplex print mode.
∗ To set the copy magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the scan mode to be adjusted
with 10-key. (Select one of 3 - 5.)
2) Press [START] key.
50-10
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image off-center position.
(Adjusted separately for each paper feed section.)
Section
Item Picture quality Image position
Item Set range Default
0 TRAY SELECT Paper feed tray selection 1 - 6 –
1 COPY START Copy START (Default) ––
2 MAGNIFICATION Print magnification ratio 25 - 400% 100
(Off-center adjustment value)
3 TRAY1 Tray 1 adjustment 0 - 99 50
4 TRAY2 Tray 2 adjustment
5 TRAY3 Tray 3 adjustment
6 TRAY4 Tray 4 adjustment
7 BPT Manual feed tray
adjustment
8 LCC Side LCC adjustment
9 ADU Adjustment when paper is
fed again from ADU
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed
6 LCC Side LCC
Set range 25 - 400 (%)
Select 0, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
50-12
Purpose Adjustment
Function
(Purpose)
Used to adjust the scan image off-center position.
(Adjusted separately for each scan mode.)
Section
Item Picture quality Image position
Item Set range Default
0 TRAY SELECT Paper feed tray
selection
1 - 5 –
1 COPY START Copy START (Default) ––
2 MAGNIFICATION Print magnification ratio 25 - 400% 100
(Resist adjustment value)
3 PLATEN OC mode adjustment 0 - 99 50
4 SPF SIDE1 SPF front surface
adjustment
5 SPF SIDE2 SPF back surface
adjustment
50
2
Select 1,
and press
[START] key.
Select other than 0 - 2, and
press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA)
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
6.TRAY4 50 7.BPT 50 8.LCC 50 9. ADU 50
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
2.TRAY1
1
SIMULATION 50-10
PRINT OFF-CENTER
ADJUSTMENT. SELECT 1-16, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
To Next Page
Loading...
