: Feb. 9 2004
1
AR-M550/M620/M700 SIMULATION 8 - 74
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 2 - 12.)
2) Press [START] key.
(Resist adjustment)
1) Enter the resist adjustment value with 10-key.
2) Press [START] key.
When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed tray
selection mode.)
3) Enter the number corresponding to the paper feed tray to be used
with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering the adjustment value in
this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.
Scanner mode
10 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
0
(0mm)
11 OC (FRONT/REAR) OC side
12 OC (TRAIL_EDGE) OC rear edge
13 SPF (LEAD_EDGE) SPF lead edge
14 SPF (FRONT/REAR) SPF side
15 SPF (TRAIL_EDGE) SPF rear edge
16 CIS (LEAD_EDGE) CIS lead edge
17 CIS (FRONT/REAR) CIS side
18 CIS (TRAIL_EDGE) CIS rear edge
Press [START] key. Press [CUSTOM SETTINGS] key.
51
51-2
Purpose Adjustment
Function
(Purpose)
Used to adjust the contact pressure of paper on the
resist roller of each section (each paper feed, duplex
feed and SPF paper feed of the copier). (This
adjustment is required when the print image position
variations are considerably great or when paper jams
occur frequently.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Item
Set
range
Default
AR-M550N/U,
AR-620N/U
AR-
M700N/U
0 TRAY SELECT Paper feed tray
selection
(1 - 5)
––
–
1 PRINT START Print start (Default) ––
–
2 TRAY1 Tray 1 adjustment value
0 - 99 46 48
3 TRAY2 Tray 2 adjustment value
45
46
4 TRAY3 Tray 3 adjustment value
46
47
5 TRAY4 Tray 4 adjustment value
6 BPT Manual feed tray resist
adjustment value
45
46
7 LCC Side LCC resist
adjustment value
8 ADU ADU resist adjustment
value
43
46
9 SPF (TOP) SPF resist adjustment
value (Top speed)
50
Item Set range Default
1
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
1
10 SPF (HIGH) SPF resist adjustment
value (High speed)
0 - 99 50
11 SPF (LOW) SPF resist adjustment
value (Low speed)
12 SPF FEED
(TOP)
SPF paper fed resist
adjustment value (Top
speed)
0 - 99 50
13 SPF FEED
(HIGH)
SPF paper feed resist
adjustment value (High
speed)
14 SPF FEED
(LOW)
SPF paper feed resist
adjustment (Low speed)
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual feed
6LCC LCC
Item
Set
range
Default
AR-M550N/U,
AR-620N/U
AR-
M700N/U
1
To Next Page
Loading...
