AR-M550/M620/M700 SIMULATION 8 - 81
Operation/Procedure
1) Select YES/NO of deleting the document filing data.
2) Press [START] key.
During formatting, "EXECUTING" is displayed. When formatting is
completed normally, "OK" is displayed. If not, "NG" is displayed.
NOTE: When executed, this function internally executes the same
function as SIM66-10;deleting reservation data, bulletin board
data, and confidential data.
Operation/Procedure
Operation/Procedure
1) Enter the number corresponding to the shading mode to be exe-
cuted.
2) Press [START] key.
During execution, "EXECUTING" is displayed. When execution is com-
pleted normally, "COMPLETED" is displayed.
Operation/Procedure
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key.
When a shading error occurs, this adjustment value is changed.
62-11
Purpose Data clear
Function
(Purpose)
Used to delete document filing data. (The management
area (standard folder, user folder) is cleared.)
Section MFP controller (HDD)
Item Clear
1 YES Execution
2 NO Cancel
Completion Press [CUSTOM SETTINGS] key.
63
63-1
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function
(Purpose)
Used to check the result of shading correction. (The
shading correction data are displayed.)
Section Optical (Image scanning)
Item Operation
CCD data
FRONT ODD GAIN Front odd-number pixel gain adjustment value
FRONT EVEN GAIN Front even-number pixel gain adjustment value
FRONT OFFSET Front black difference
REAR ODD GAIN Rear odd-number pixel gain adjustment value
REAR EVEN GAIN Rear even-number pixel gain adjustment value
REAR OFFSET Rear black difference
MIN All pixels min. value
MAX All pixels max. value
AVE All pixels average value
CIS data (Only when DSPF installed.)
GAIN Gain adjustment value
MAX Pixel max.
MIN Pixel min.
AVE Pixel average
OFFSET Black difference
DEV Standard deviation
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR. EXECUTING···.
Press [START] key.
SIMULATION 62-11
DOCUMENT FILING DATA CLEAR.
OK. (or NG)
63-2
Purpose Adjustment
Function
(Purpose)
Used to execute shading.
Section Optical (Image scanning)
Item Operation
1 OC SHADING OC analog level correction and shading
correction (Document table mode)
2 DSPF SHADING DSPF analog level correction and shading
correction
Completion Press [CUSTOM SETTINGS] key.
63-7
Purpose Adjustment
Function
(Purpose)
Used to adjust the white plate scan start position for
shading. (Document table mode)
Section Laser (Exposure)
Item Operation
Item Set range Default
1 CCD CCD scan 1 - 16 6
SIMULATION 63-1
SHADING DATA DISPLAY.
(CCD)
FRONT ODD GAIN: 128 FRONT EVEN GAIN: 255
FRONT OFFSET: 2
REAR ODD GAIN: 128 REAR EVEN GAIN: 255
REAR OFFSET: 2
MIN.: 255 MAX.: 0 AVE.: 255
(CIS)
GAIN: 128 OFFSET: 0 MAX.: 255
MIN.: 255 AVE.: 255 DEV.: 0
SIMULATION 63-2
SHADING EXECUTION. SELECT1-2, AND PRESS START.
1. OC SHADING
2. DSPF SHADING
1
SIMULATION 63-2
SHADING EXECUTING···.
1. OC SHADING
Press [START] key.
SIMULATION 63-2
SHADING COMPLETED.
1. OC SHADING
1
To Next Page
Loading...
