Sharp AR-M550N - Page 348

AR-M550/M620/M700 SIMULATION 8 - 90
Operation/Procedure
1) Enter the dial number with 10-key.
Use 10-key, [*] key, and [#] key to enter the number. The upper
limit is 20 digits.
When [CLEAR] key is pressed, the mode returns to the initial state.
2) Press [START] key.
Operation/Procedure
1) Enter 0 with 10-key.
2) Press [START] key.
The dial signal is outputted.
(Dial pulse make time setting)
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
The dial signal is sent with the set value + 29ms.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
Operation/Procedure
1) Enter 0 with 10-key.
2) Press [START] key.
The dial signal is outputted.
(Dial pulse make time setting)
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
The dial signal is sent with the set value + 9ms.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
Same display Select 3 and press [START] key.
66-13
Purpose Setting
Function
(Purpose)
Used to enter (set) the number of FAX dial signal
output test. (The dial number set by this simulation is
outputted when the dial signal output test is made by
SIM 66-14 - 16. ) (Only when FAX is installed)
Section FAX
Item Data
66-14
Purpose Setting/Operation test/Check
Function
(Purpose)
Used to set the make time in the FAX pulse dial mode
(10pps) and to test the dial signal output. (The dial
number signal set by SIM 66-13 is outputted.) Used to
check troubles in dialing and to check the operation.
(Only when FAX is installed)
Section FAX
Item Operation
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
1. NO SIGNAL 2. 11111 3. 11110 4. 00000
5. 010101 6. 00001
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING···.
1. NO SIGNAL 2. 11111 3. 11110 4. 00000
5. 010101 6. 00001
1
1
Press [START] key. Press [CUSTOM SETTING] key.
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
START.
EXECUTING···.
1. NO SIGNAL 2. 11111 3. 11110 4. 00000
5. 010101 6. 00001
2
Press [CUSTOM SETTINGS] key.
SIMULATION 66-13
DIAL TEST NUMBER SETTING. 0-9:[0-9], *:[*], #:[#]
INPUT NUMBER AND PRESS START.
0123456789*#01234567
0 EXECUTE Execute
1 MAKE TIME Dial pulse make time setting (0 - 15)
66-15
Purpose Setting/Operation test/Check
Function
(Purpose)
Used to set the make time in the FAX pulse dial mode
(20pps) and to test the dial signal output. (The dial
number signal set by SIM 66-13 is outputted.) Used to
check troubles in dialing and to check the operation.
(Only when FAX is installed)
Section FAX
Item Operation
0 EXECUTE Execute
1 MAKE TIME Dial pulse make time setting (0 - 15)
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1. MAKE TIME]
1
7
SIMULATION 66-14
DIAL TEST(10PPS). EXECUTE
1. MAKE TIME 7 ; [+29 ms]
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1. MAKE TIME 7 ; [+29 ms]
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key
or press [START] key.
Select 1 and
press [START] key.
Select 0
and press
[START] key.