Sharp Gemini II Plus MX-2614N

Simulation Codes
31
Document Solutions After Sales Service
56
MFP Data Import / Export
1 Transfer data execute
2 EEPROM, SD Card & HDD backup to USB
3 Document filing backup to USB
4 Job log data backup to USB
5 Import 22-06 to USB (text format)
11
Copy SD card data to HDD
12 Copy SD card data to HDD
60
Memory Operation / Test
1 Check memory operation (read/write) of MFP
61
LSU Adjustment
1 LSU test (Polygon motor & Laser detection check)
3 Laser power setting
4 LSU image skew adjustment pattern
62
HDD Operation / Test
1 HDD and SD card format (FAT32)
2 HDD partial read/write check
3 HDD read/write check (All)
6
Smart (HDD) self diagnostics test (E7-03)
7 Smart (HDD) self diagnostics error log
8 HDD and SD card format (excluding system &
operation manual area)
10 Used to delete the Job Log data
11
Used to delete the Document Filing data
12 Enable/Disable auto format for HDD trouble
13 HDD format (Operation Manual and Watermark
data area only)
14 Delete document filing management data
15 Convert setting data for document filing reprint
63
CCD Operation / Adjustment
1 Shading correction data display
2 Shading correction execution (force)
3
CCD gamma & colour balance auto adjustment
4
SIT chart patch density display
5 CCD gamma & colour balance setup (Default)
6 Print engine colour balance (chart reading)
7 Standard target colour calibration set-up
(Service)
8
Standard scanner target default (Service Mode)
11 Colour Balance setting (Factory Mode).
64
Self Test Print
1
Self print test (Colour mode)
2 Engine colour balance patch print mode
4 Printer self print test (256 gradations)
64
Self test cont…
5
Printer self print test (PCL)
6 Printer self pint test (PS)
7 Print adjustment pattern (SIM 46-21)
65
LCD Operation / Adjustment
1 LCD touch panel adjustment
2 LCD touch panel adjustment display
5
Operation panel key input check
66
Fax Operation / Adjustment
1 FAX Soft SW setting (2-99)
2 Country code default set (FAX)
3
FAX PWB controller memory check
4 FAX signal line check (Max level)
5 FAX signal line check (Soft SW setting)
6 FAX check list print (confidential registration)
7 FAX memory printout (all data)
8
FAX voice message setup
9
FAX signal (sound) line check (Soft SW setting)
10 FAX all memory clear
11 Voice signal check (line & speaker 300bps - Max)
12 Voice signal check (line & speaker 300bps –Soft
SW)
13
Register dial number for Sim 66-14/15/16
14 Adjust & check the time dial pulse (10bps)
15 Adjust & check the time dial pulse (20bps)
16 Adjust and check the send level DTFM signal
17 Select DTFM signal to send to line (Max level)
18
Select DTFM signal to send to line (Soft SW)
21
Print various registration information
22 Set the sound volume of the handset
24 Fast save data clear
29 FAX address book clear
30 Tel/LIU sensor status check
31
ON/OFF setting of each output port (Tel/LIU)
32 Received data check
33 Busy Tone/CNG/CED/FNET/DTMF detect signal
check
34 Communication time display
36
Check Send/Receive from modem controller
39
Check Destination saved in FAX EEPROM
42 Rewrite PIC program installed on FAX box
43 Write program & adjustment values to PIC
installed on FAX
61 Display the FAX related soft SW (151-250)
62
Import FAX data to USB