Sharp MX-M620N

MX-M700N SIMULATION 7 – 40
46-16
Purpose
Adjustment
Function (Purpose)
Used to adjust the print density in the FAX
mode (each ultra fine mode). (Only when
FAX is installed.)
Section
—
Operation/Procedure
1) Select the number corresponding to one of the following
adjustment items with 10-key. (Select one of 3 - 14.)
* Normal mode (Print density adjustment level)
* Normal mode (Print density adjustment level) (Half-tone
mode)
* Auto mode
* Auto mode (Half-tone mode)
2) Press the [START] key.
3) Enter the print density level with 10-key.
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, printing is performed and the
adjustment value is set simultaneously.
Check the density of printed image.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
46-17
Purpose
Setting
Function (Purpose)
Used to set the gain in shading correction.
Section
Optical (Image scanning) - CCD, CIS
Operation/Procedure
1) Select the number corresponding to the adjustment item with
10-key.
2) Press the [START] key.
3) Enter the shading gain change value with 10-key.
4) Press the [START] key.
There is normally no need to change the shading gain with this sim-
ulation.
Only when the scanned image density is unsatisfactory though
shading is performed, the above procedure is performed.
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level
selection
3 AUTO Auto 0 - 99 50
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
9 AUTO (H) Auto (Half-tone)
10 1.0 (H) Exposure level 1
(Half-tone)
11 2.0 (H) Exposure level 2
(Half-tone)
12 3.0 (H) Exposure level 3
(Half-tone)
13 4.0 (H) Exposure level 4
(Half-tone)
14 5.0 (H) Exposure level 5
(Half-tone)
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
Item
Setting
range
Default
1 CCD FRONT ODD 0 - 255 112
2 CCD FRONT EVEN
3 CCD REAR ODD
4 CCD REAR EVEN
5CIS 128
1
SIMULATION 46-16
EXP.LEVEL SETUP FAX(ULTRA FINE).SELECT 0-14,AND PRESS
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50 5.2.0 50
6.3.0 50 7.4.0 50 8.5.0 50
9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50
12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
SIMULATION 46-17
CCD/CIS SHADING GAIN DATA SETUP. SELECT 1-5, AND
PRESS START.
1. CCD FRONT ODD 128 2. CCD FRONT EVEN 128
3. CCD REAR ODD 128 4. CCD REAR EVEN 128
5. CIS 128