Sharp MX-M620N

MX-M700N SIMULATION 7 – 53
50-12
Purpose
Adjustment
Function (Purpose)
Used to adjust the scan image off-center
position. (Adjusted separately for each
scan mode.)
Section
—
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the scan mode to be
adjusted with 10-key. (Select one of 3 - 5.)
2) Press the [START] key.
(Scan off-center position adjustment)
1) Enter the scan image off-center position adjustment value with
10-key.
2) Press [P] key or [START] key.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the off-center of the printed image.
Repeat the above adjustments until acceptable results are
obtained.
(UNIT: 0.1mm/step When the adjustment value is increased, the
print image is shifted to the front direction.)
(Copy condition setting in this simulation)
* To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 6) and 10 is entered,
the mode is changed to the duplex print mode.
* The copy magnification ratio can be set with the following pro-
cesures.
1) Enter 2 with 10-key.
2) Press the [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press the [START] key.
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
50-27
Purpose
Adjustment
Function (Purpose)
Used to adjust the image loss of the scan
image in the FAX/scan mode.
Section
—
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the adjustment item with
10-key.
2) Press the [START] key.
3) Enter the adjustment value with 10-key.
4) Press the [START] key.
(Shift for the adjustment value change: 1.0mm/step)
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 - 6 -
1 COPY START Copy START
(Default)
--
2MAGNIFICATIO
N
Print magnification
ratio
25 - 400% 100
(Resist adjustment value)
3 PLATEN OC mode adjustment 0 - 99 50
4 SPF SIDE1 SPF front surface
adjustment
5 SPF SIDE2 SPF back surface
adjustment
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
Setting range 25 - 400 (%)
Item
Setting
range
Default
FAX send
1OC
(LEAD_EDGE)
OC lead edge 0 - 10
(Unit
1mm)
3
(3mm)
2 OC (FRONT/
REAR)
OC side
3OC
(TRAIL_EDGE)
OC rear edge
4 SPF
(LEAD_EDGE)
SPF lead edge
5 SPF (FRONT/
REAR)
SPF side
6 SPF
(TRAIL_EDGE)
SPF rear edge
7CIS
(LEAD_EDGE)
CIS lead edge
8 CIS (FRONT/
REAR)
CIS side
9CIS
(TRAIL_EDGE)
CIS rear edge
2
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA)
3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50