Sharp MX-M620N

MX-M700N SIMULATION 7 – 54
51
51-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the contact pressure of
paper on the resist roller of each section
(each paper feed, duplex feed and SPF
paper feed of the copier). (This adjustment
is required when the print image position
variations are considerably great or when
paper jams occur frequently.)
Section
Paper transport (Discharge/Switchback/
Transport)
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 2 - 14.)
Changing the resist amount value by 1shifts the position by
1ms.
2) Press the [START] key.
(Resist adjustment)
1) Enter the resist adjustment value with 10-key.
2) Press the [START] key.
When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.
(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 6) and 10 is entered,
the mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
Item
Setting
range
Default
Scanner mode
10 OC
(LEAD_EDGE)
OC lead edge 0 - 10
(Unit
1mm)
0
(0mm)
11 OC (FRONT/
REAR)
OC side
12 OC
(TRAIL_EDGE)
OC rear edge
13 SPF
(LEAD_EDGE)
SPF lead edge
14 SPF (FRONT/
REAR)
SPF side
15 SPF
(TRAIL_EDGE)
SPF rear edge
16 CIS
(LEAD_EDGE)
CIS lead edge
17 CIS (FRONT/
REAR)
CIS side
18 CIS
(TRAIL_EDGE)
CIS rear edge
Item
Setting
range
Default
55/62
(ppm)
70
(ppm)
0TRAY
SELECT
Paper feed tray
selection (1 - 6)
-
- -
1 PRINT
START
Print start (Default) -
- -
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
1
2 TRAY1 Tray 1 resist
adjustment value
0 - 99 40 48
3 TRAY2 Tray 2 resist
adjustment value
39 46
4 TRAY3 Tray 3 resist
adjustment value
40 47
5 TRAY4 Tray 4 resist
adjustment value
6 BPT Manual feed tray
resist adjustment
value
39 46
7 LCC Side LCC resist
adjustment value
8 ADU ADU resist
adjustment value
9SPF
(TOP)
SPF resist
adjustment value
(Top speed)
50 50
10 SPF
(HIGH)
SPF resist
adjustment value
(High speed)
11 SPF
(LOW)
SPF resist
adjustment value
(Low speed)
12 SPF
FEED
(TOP)
SPF paper feed
resist adjustment
value (Top speed)
13 SPF
FEED
(HIGH)
SPF paper feed
resist adjustment
value (High speed)
14 SPF
FEED
(LOW)
SPF paper feed
resist adjustment
(Low speed)
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6LCC LCC
Item
Setting
range
Default
55/62
(ppm)
70
(ppm)
1
: '07 Feb 15
1