To Next Page
K
Kayla BellSep 23, 2025
What to do if Siemens Transmitter displays 'Current output disabled'?
- JJason WheelerSep 23, 2025
If the current output is disabled, turn on current output.
What to do if Siemens Transmitter displays 'Current output disabled'?
If the current output is disabled, turn on current output.
How do I fix 'Incorrect or no coil current' on Siemens 7ME6910?
If there is incorrect or no coil current, check the cables and connections.
What does it mean if my Siemens 7ME6910 Transmitter says 'Pulse overflow'?
A pulse overflow indicates that the actual flow is too big compared with pulse width and volume/pulse. Reduce the pulse width.
What to do if Siemens 7ME6910 displays 'Empty pipe error'?
If you see an empty pipe error, switch off the MAG 5000/6000/6000 I, wait 5 seconds, and then switch it on again.
What to do if Siemens 7ME6910 Transmitter shows 'Reverse flow direction'?
If the flow direction is reversed, change the direction.
What does 'Batch timeout' mean on my Siemens 7ME6910 Transmitter, and how do I fix it?
If the duration of batching has exceeded a predefined maximum time, set the batch output to zero.
What to do if Siemens Transmitter displays 'Negative flow direction during batch'?
If there's a negative flow direction during batch, check the flow direction.
What does 'Batch overrun' mean on my Siemens Transmitter, and how do I fix it?
If the batch volume has exceeded a predefined maximum overrun volume, set the batch output to zero.
What to do if Siemens 7ME6910 Transmitter displays 'Defective SENSORPROM® unit'?
If the SENSORPROM® unit is defective, replace it.
What should I do if my Siemens Transmitter displays 'Internal conversion error in ASIC'?
If there is an internal conversion error in ASIC, replace the transmitter.
Covers general requirements for installation and instrument safety standards.
Lists relevant EU directives like EMC, LVD, and ATEX the device complies with.
Specifies conditions and requirements for installing the device in hazardous areas.
Step-by-step guide for installing the compact version of the transmitter.
Instructions for installing the transmitter in a remote configuration.
Provides detailed wiring diagrams and connection instructions for power supply and signals.
Specific electrical connection details for PTB K7.2 approved MAG 5000/6000 CT.
Steps for commissioning the blind version without a display.
Explains the display symbols and fields of the local user interface.
Outlines the operator and setup menu structure and navigation methods.
Procedure for changing the transmitter's password for enhanced security.
Details how to configure fundamental parameters like frequency and flow direction.
Configuration options for current, digital, and relay outputs.
Describes how to use digital inputs for control functions like batch start/stop.
Procedures for resetting totalizers or restoring factory settings.
Guide for troubleshooting transmitter issues and performing basic checks.
Explains the error system, acceptance levels, and status/error logging.
Comprehensive table of error codes, their causes, and recommended remedies.
A high-level map of the transmitter's menu structure and navigation.
Visual diagrams of the basic settings menu options and configurations.
Menu diagram for reset and default setting operations.
Specific menu diagram for reset modes on MAG 6000 SV.
Menu diagram illustrating service mode functions.
General| Model | 7ME6910 |
|---|---|
| Manufacturer | Siemens |
| Product Type | Transmitter |
| Measurement Principle | Electromagnetic |
| Process Connection | Flange |
| Output Signal | 4-20 mA, HART |
| Power Supply | 24 V DC |
| Accuracy | ±0.2% of flow rate |
| Operating Temperature | -20 to +60 °C |
| Ambient Temperature Range | -40 to +85 °C |
| Process Temperature Range | -40°C to +180°C (depending on liner material) |
| Housing Material | Aluminum |
| Protection Class | IP67 |
| Certifications | ATEX, IECEx |
