To Next PageTo Next PageWhat does it mean if my Siemens 7ME6910 says 'The SENSORPROM® unit ID does not comply with the product ID'?
If the SENSORPROM® unit ID does not comply with the product ID, it means the SENSORPROM® unit is from another type of product SITRANS F C, SITRANS F US etc. Replace the SENSORPROM® unit.
What should I do if the Siemens 7ME6910 shows 'Measuring pipe empty'?
If the measuring pipe is empty, ensure that the measuring pipe is full.
What to do if Siemens 7ME6910 displays 'Coil excitation has failed'?
If the coil excitation has failed, check the cables.
What should I do if my Siemens Transmitter displays 'Internal conversion error in ASIC'?
If there is an internal conversion error in ASIC, replace the transmitter.
How to fix a 'Current output' issue on a Siemens 7ME6910 Transmitter?
If there's a current output issue, it could be due to a disconnected current loop or excessive loop resistance. Check the cables.
What to do if Siemens Transmitter shows 'Totalizer 2 Reset manually'?
If 'Totalizer 2 Reset manually' is displayed, it's because the check of the saved totalizer value failed during initialization, making it unreliable. The totalizer value must be reset manually to ensure future readings are accurate.
What to do if Siemens 7ME6910 Transmitter shows 'Totalizer 1 Reset manually'?
If 'Totalizer 1 Reset manually' is displayed, it's because the check of the saved totalizer value failed during initialization, making it unreliable. The totalizer value must be reset manually to ensure future readings are accurate.
How to resolve 'Totalizer roll over' on Siemens Transmitter?
If the totalizer rolls over, reset the totalizer or increase the totalizer unit.
What to do if Siemens 7ME6910 Transmitter shows 'Reverse flow direction'?
If the flow direction is reversed, change the direction.
What to do if Siemens 7ME6910 displays 'Empty pipe error'?
If you see an empty pipe error, switch off the MAG 5000/6000/6000 I, wait 5 seconds, and then switch it on again.
General| Model | 7ME6910 |
|---|---|
| Manufacturer | Siemens |
| Product Type | Transmitter |
| Measurement Principle | Electromagnetic |
| Process Connection | Flange |
| Output Signal | 4-20 mA, HART |
| Power Supply | 24 V DC |
| Accuracy | ±0.2% of flow rate |
| Operating Temperature | -20 to +60 °C |
| Ambient Temperature Range | -40 to +85 °C |
| Process Temperature Range | -40°C to +180°C (depending on liner material) |
| Housing Material | Aluminum |
| Protection Class | IP67 |
| Certifications | ATEX, IECEx |
Covers general requirements for installation and instrument safety standards.
Lists relevant EU directives like EMC, LVD, and ATEX the device complies with.
Specifies conditions and requirements for installing the device in hazardous areas.
Step-by-step guide for installing the compact version of the transmitter.
Instructions for installing the transmitter in a remote configuration.
Provides detailed wiring diagrams and connection instructions for power supply and signals.
Specific electrical connection details for PTB K7.2 approved MAG 5000/6000 CT.
Steps for commissioning the blind version without a display.
Explains the display symbols and fields of the local user interface.
Outlines the operator and setup menu structure and navigation methods.
Procedure for changing the transmitter's password for enhanced security.
Details how to configure fundamental parameters like frequency and flow direction.
Configuration options for current, digital, and relay outputs.
Describes how to use digital inputs for control functions like batch start/stop.
Procedures for resetting totalizers or restoring factory settings.
Guide for troubleshooting transmitter issues and performing basic checks.
Explains the error system, acceptance levels, and status/error logging.
Comprehensive table of error codes, their causes, and recommended remedies.
A high-level map of the transmitter's menu structure and navigation.
Visual diagrams of the basic settings menu options and configurations.
Menu diagram for reset and default setting operations.
Specific menu diagram for reset modes on MAG 6000 SV.
Menu diagram illustrating service mode functions.
