Siemens SIPROTEC4 7UM62 User Manual

Table of contents
viii
SIPROTEC Modbus - Bus mapping
C53000-L1840-C009-03
2.2.12 Registers 10051 to 10058: Frequency protection................................................................2-7
2.2.13 Registers 10059 to 10063: Overexcitation protection..........................................................2-7
2.2.14 Registers 10064 to 10066: Reverse power protection.........................................................2-7
2.2.15 Registers 10067 to 10070: Forward power supervision ......................................................2-7
2.2.16 Register 10071: Fuse Failure Monitor .................................................................................2-8
2.2.17 Registers 10072 to 10077: Underexcitation protection........................................................2-8
2.2.18 Registers 10078 to 10079: Circuit breaker failure protection...............................................2-8
2.2.19 Registers 10080 to 10087: Impedance protection...............................................................2-8
2.2.20 Registers 10088 to 10091: Binary inputs.............................................................................2-9
2.2.21 Registers 10092 to 10093: Inadvertent energisation protection ..........................................2-9
2.2.22 Register 10094: Trip coil monitor.........................................................................................2-9
2.2.23 Registers 10095 to 10096: Inverse undervoltage protection ...............................................2-9
2.2.24 Registers 10097 to 10099: Startup supervision of motors...................................................2-9
2.2.25 Register 10100: Startup counter for motors....................................................................... 2-10
2.2.26 Registers 10101 to 10102: Rotor ground fault protection (R,fn)........................................ 2-10
2.2.27 Registers 10103 to 10104: DC voltage/current protection.................................................2-10
2.2.28 Registers 10105 to 10108: State of the out-of-step protection ..........................................2-10
2.2.29 Registers 10109 to 10115: Differential protection.............................................................. 2-10
2.2.30 Registers 10116 to 10117: Stator ground fault protection 100%....................................... 2-11
2.2.31 Registers 10118 to 10119: Rotor ground fault protection 1-3 Hz ......................................2-11
2.2.32 Registers 10120 to 10121: Restricted ground fault protection........................................... 2-11
2.2.33 Registers 10122 to 10129: Fault indications of protection functions ................................. 2-11
2.3 Input registers (3X references) ..........................................................................................2-12
2.4 Holding registers (4X references)...................................................................................... 2-13
2.4.1 Registers 40001 to 40036: System information................................................................. 2-13
2.4.2 Registers 40065 to 40069: Time synchronization.............................................................. 2-13
2.4.3 Register 40129: Diagnosis................................................................................................. 2-14
2.4.4 Registers 40201 to 40208: Metered measurands.............................................................. 2-15
2.4.5 Register 40251: Measured values in output direction........................................................2-15
2.4.6 Registers 40301 to 40324: Statistic values........................................................................2-16
2.4.7 Registers 40351 to 40410: Min/Max values of measured values ......................................2-17
3 Standard mapping 3-2 ......................................................................................................................3-1
3.1 Coil Status registers (0X references)...................................................................................3-2
3.1.1 Registers 00001 to 00010: Internal Commands ..................................................................3-2
3.1.2 Registers 00011 to 00026: Single commands and taggings ...............................................3-2
3.1.3 Registers 00027 to 00030: Double commands....................................................................3-3
3.1.4 Registers 00257 to 00264: Exception Flags........................................................................3-3
3.2 Input Status registers (1X references).................................................................................3-4
3.2.1 Registers 10001 to 10008: User-defined annunciations......................................................3-4
3.2.2 Registers 10009 to 10013: Overcurrent time protection I>..................................................3-4
3.2.3 Registers 10014 to 10019: Overcurrent time protection I>>................................................3-4
3.2.4 Registers 10020 to 10023: Inverse time overcurrent protection..........................................3-5

Siemens SIPROTEC4 7UM62 Specifications

General

Brand	Siemens
Model	SIPROTEC4 7UM62
Category	Conference System
Language	English