35
GB
13. Using the citrus press
Application area:
The citrus press, consisting of the screen18 and one of the
juicer cones20 + 21, is suitable for squeezing halved cit-
rus fruits. Use the small juicer cone20 for small citrus fruits
(e.g. lemons, limes) or the large juicer cone21 for larger
citrus fruits (e.g. oranges).
WARNING! Risk of material damage!
~ Ensure that there are no foreign objects on the
screen18 or in the device when operating it.
~ Do not put excessive pressure on the juicer cone20/
21.
Processing table:
WARNING! Risk of material damage!
~ Do not operate the device continuously with the citrus
press18 + 20/21 in place for more than 7 minutes.
After this, the device must remain switched off until it
has cooled down to room temperature.
Required accessories:
- Working container9
-Axle17
-Screen18
- Small juicer cone20 or large juicer cone21
And this is how it works:
1. Position the working container9 on the base unit13.
Turn the working container slightly in a clockwise di-
rection until it is heard to lock into place.
2. Figure K: place the axle17 into the working con-
tainer9.
3. Figure K: position the screen18 on the working
container9 and the axle17. Turn the screen slightly
in a clockwise direction until it is heard to lock into
place.
4. Figure L: place the juicer cone20/21 in the centre
of the screen18.
5. Connect the mains plug10 to a wall socket.
6. Use the dial12 to select position 1.
7. Exert slight pressure on the halves of the citrus fruit
when pushing the cut surface down onto the rotating
juicer cone20/21. The juice flows into the working
container9.
NOTES:
• For the best juice yield, press the citrus fruit halves
down vertically first of all. Then move them on the juic-
er cone20/21 slightly in all directions back and forth
until the entire pulp has been processed.
• If the juicer cone20/21 does not turn check if there
are any pips between the juicer cone and the
screen18 and remove them if necessary.
• If a lot of pulp and pips have accumulated in the
screen18 remove the mains plug10 and empty the
screen.
8. Stop the process at the latest when the maximum fill-
ing height for liquids (1250 ml) is reached in the
working container9.
9. When the process is completed, switch the dial12 to
0 and pull out the mains plug10.
10. Turn the screen18 slightly anticlockwise and remove
it together with the juicer cone20/21.
11. Remove the axle17.
12. Turn the working container9 slightly in an anticlock-
wise direction and remove it.
13. Pour the juice out of the working container9.
14. Clean all of the accessories that have been used im-
mediately if possible.
14. Mini crusher
Application area:
The mini crusher, consisting of the mini container16 and
the blade unit15, are suitable for chopping and crashing
a small amount of onions, herbs, nuts, coffee beans and
parmesan.
WARNING! Risk of material damage!
~ The mini crusher must not be operated with liquids.
Processing table:
WARNING! Risk of material damage!
~ Do not operate the device continuously with the mini
crusher15 + 16 in place for more than 2 minutes. Af-
ter this, the device must remain switched off until it has
cooled down to room temperature.
Required accessories:
- Mini container16
- Blade unit15
- Sealing ring14
And this is how it works:
1. Do not fill the ingredients into the mini container16
above the MAX mark. Read the instructions in the
processing table carefully.
2. Place the sealing ring14 on the blade unit15.
3. Figure E: place the blade unit15 with the blades
facing downward on the mini container16.
4. Figure E: rotate the blade unit15 anticlockwise
until it sits firmly on the mini container16.
5. Figure F: turn the assembled mini crusher15 + 16
around and place it on the base unit13. Turn the
Ingredients max. quantity Processing time
Switch
Oranges 5 pieces (in halves) approx. 4 - 6 min.
1
Ingredients max. quantity Processing time
Switch
Almonds 150 g 8 - 10 x 1 sec.
P
Coffee
beans
50 g
approx.
30 - 60 sec.
2
__326488_Kuechenmaschine Multi_B8.book Seite 35 Dienstag, 6. August 2019 10:40 10
To Next Page
Loading...
