Sony SLV-D360P - Page 24

1-14
58
Recording TV programs using the VCR Plus+
®
system (SLV-D560P only)
To stop recording
To stop the VCR while recording, press x STOP.
To use the DVD-VCR after setting the timer
To use the DVD-VCR before a timer recording begins, just press ?/1. The timer
indicator disappears from the display window and the DVD-VCR switches on.
Remember to press ?/1 to reset the VCR to the timer recording standby mode after
using the VCR.
Yo u can also do the following tasks while the VCR is recording:
•Reset the counter (page 44).
•Display tape information on the TV screen (page 46).
•Check the timer settings (page 59).
•Watch another TV program (page 47).
Tip
•To check, change or cancel the program setting, see “Checking/changing/canceling timer
settings” on page 59.
Notes
• If the VCR does not accept the PlusCode number, this means that:
–The PlusCode number is incorrect.
–“Once,” “Daily,” “Mo~Sa,” “Mo~Fr” or “Weekly” was selected incorrectly. You cannot
select “Daily,” “Mo~Sa,” “Mo~Fr” or “Weekly” for a program that airs more than seven
days ahead.
Correctly set the PlusCode number again from step 2.
•When the PlusCode number is incorrect, “Invalid code” will appear in the display.
59
Checking/changing/canceling timer settings
Basic Operations
Checking/changing/canceling timer
settings
Before you start…
•Check that the DVD-VCR clock is set to
the correct time.
•Turn on the DVD-VCR and your TV.
•Switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
•Set TV
/ DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 10).
•When using a decoder, turn it on.
•Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1
Press SET UP, then press V/v to select
(PROGRAM) and press ENTER. You can also
display the timer programming menu by
pressing TIMER.
The timer programming menu appears.
2
Press V/v to select setting you want to change
or cancel.
•To change the setting, press B/b to select
the item you want to change, and press V/v
to change it.
•To cancel the setting, press CLEAR.
TIMER
CLEAR
SET UP
V/v/B/b
ENTER
O RETURN
CH START END DATE
RETURN
SPEED
vV bB
01 05 31
P
M
07 31
P
M
1/20
Auto
SP
03 01 31
A
M
03 32 1/21
A
M
06 06 32 08 32
P
M
P
M
1/21 EP
CH START END DATE
RETURN
SPEED
v
V
b
B
01 05 31
P
M
07 31
P
M
1/20
Auto
SP
03 01 31
A
M
03 32 1/21
A
M
06 06 32 08 32
P
M
P
M
1/21 EP
CLEAR
continued
60
Checking/changing/canceling timer settings
When the timer settings overlap
The program that starts first has priority and the second program starts recording only
after the first program has finished. If the programs start at the same time, the
program listed first in the menu has priority.
Tip
• If the indicator appears, the timer settings overlap.
3
Press O RETURN to confirm the setting.
Press O RETURN again to exit the menu.
Program 1
Program 2
about 20 seconds will be cut off
Program 1
Program 2
about 20 seconds
will be cut off
61
Locking the DVD-VCR (Child Lock)
Basic Operations
Locking the DVD-VCR (Child Lock)
After you have set the timer, you can lock all
of the buttons on the DVD-VCR so that the
settings are not canceled by mistake.
To lock the DVD-VCR
When the DVD-VCR is turned on, hold down ?/1 POWER on the unit
until “LOCK”
appears in the display window. The DVD-VCR turns off and the indicator
remains lit if there is a timer setting. The DVD-VCR will not work except for timer
recordings.
To unlock the DVD-VCR
Hold down ?/1 POWER on the unit
until “LOCK” disappears from the display
window. The DVD-VCR is unlocked and turns on.
To stop timer recording while the DVD-VCR is locked, press x. The recording stops
and the DVD-VCR is unlocked.
Note
•The DVD-VCR will be unlocked when:
–You stop timer recording by pressing x .
–You insert a tape.
–The AC power cord is disconnected or power supply stops.
?/1 POWER