2. For one-piece body, qty. 2 are required for item 6 and item 18; for a clamped body, qty. 3 are required.
3. For valve with Tef Flow® P design stem only.
4. Unless otherwise noted, quantity required is 1.
5. EPDM recommended on all steam-contact seals.
6. POA = Part # on availability; N/A = not available with this design.
9. Part number includes lower stem and inner stem, which are assembled together.
11. Part number includes upper stem, outer stem and coupling sleeve, which are assembled together.
12. This stem used for valves with lower external flush and lower seal retainer item 17c or 17d.
,WHP
1RWHV
&RQWURO7RS
$FWXDWRU
2ULQJ2XWHU6WHPTW\ 1LWULOH 1 1 1 1 1 1
%HDULQJ8SSHU$GDSWHU 6WG
7HI)ORZ3GHVLJQ
1$
2ULQJ%RG\ (3'0 ( ( ( ( ( (
).0 9 9 9 9 9 9
D 6WHP8SSHU$VVHPEO\
E 6WHP8SSHU7HI)ORZ3'HVLJQ
32$
D 6HDW5LQJ7UL5LQJ8SSHU (3'0
).0
E
6HDW5LQJ,QVHUW8SSHU 7HI)ORZ3 32$
6HDW5LQJ7UL5LQJ9HQW (3'0
).0
D 6HDW5LQJ7UL5LQJ/RZHU (3'0
).0
E 6HDW5LQJ,QVHUW/RZHU 7HI)ORZ3 32$
D
4XDG5LQJ/RZHU (3'0
).0
E
:LSLQJ6WHP6HDO/RZHU (3'0 32$
).0 32$
%HDULQJ/RZHU6HDO5HWDLQHU
6WHP/RZHU$VVHPEO\ 32$
D 6WHP/RZHU$VVHPEO\XVHGZLWKFG 1$
E 6WHP/RZHU7HI)ORZ3'HVLJQ
32$
E /RZHU%DODQFHU7HI)ORZ3'HVLJQ
32$
25LQJ7HI)ORZ3'HVLJQ
(3'0 ( ( ( ( ( 32$
).0 9 9 9 9 9 32$
D 6HDO5HWDLQHU4XDG5LQJ
E 6HDO5HWDLQHU:LSLQJ6WHP6HDO 32$
F 6HDO5HWDLQHU/RZHU)OXVK4XDG5LQJ 32$
G 6HDO5HWDLQHU/RZHU)OXVK:LSLQJ6WHP6HDO 32$
&ODPS
6SUD\%XVKLQJ
D $GDSWHU([WHUQDO)OXVK2ULQJRU4XDG5LQJ
E $GDSWHU:LSLQJ6WHP6HDO 32$
D
2ULQJ8SSHU6WHP (3'0 ( ( ( ( ( 1$
TW\UHTXLUHG ).0 9 9 9 9 9 1$
F
4XDG5LQJ8SSHU6WHP (3'0
TW\UHT ).0
E
:LSLQJ6WHP6HDO8SSHU
(3'0
32$
).0 32$
2ULQJ)OXVK (3'0 ( ( ( ( ( (
).0 9 9 9 9 9 9
2ULQJ2XWHU6WHPTW\ 1LWULOH 1 1 1 1 1 1
3/&+
E
3DUW'HVFULSWLRQ
&RQWDFW)DFWRU\
6HHDFWXDWRUSDUWVOLVW