2. For one-piece body, qty. 2 are required for item 6 and item 18; for a clamped body, qty. 3 are required.
3. For valve with Tef Flow® P design stem only.
4. Unless otherwise noted, quantity required is 1.
5. EPDM recommended on all steam-contact seals.
6. POA = Part # on availability; N/A = not available with this design.
8. Part number includes upper stem and coupling sleeve, which are assembled together.
9. Part number includes lower stem and inner stem, which are assembled together.
10. A separate actuator stem (item 24) mates with item 8.
12. This stem used for valves with lower external flush and lower seal retainer item 17c or 17d.
,WHP
1RWHV
&RQWURO7RS
$FWXDWRU
2ULQJ,QQHU6WHP Nitrile 1 1 1 1 1 1
%HDULQJ8SSHU$GDSWHU Std.
Tef Flow® P design
1$
2ULQJ%RG\ EPDM ( ( ( ( ( (
FKM 9 9 9 9 9 9
D 6WHP8SSHU$VVHPEO\
E 6WHP8SSHU7HI)ORZ3'HVLJQ 32$
D 6HDW5LQJ7UL5LQJ8SSHU EPDM
FKM
E 6HDW5LQJ,QVHUW8SSHU Tef Flow® P 32$
6HDW5LQJ7UL5LQJ9HQW EPDM
FKM
D 6HDW5LQJ7UL5LQJ/RZHU EPDM
FKM
E 6HDW5LQJ,QVHUW/RZHU Tef Flow® P 32$
D
4XDG5LQJ/RZHU EPDM
FKM
E
:LSLQJ6WHP6HDO/RZHU EPDM 32$
FKM 32$
%HDULQJ/RZHU6HDO5HWDLQHU
6WHP/RZHU$VVHPEO\
D 6WHP/RZHU$VVHPEO\XVHGZLWKFG 32$
E
6WHP/RZHU7HI)ORZ3'HVLJQ 32$
E /RZHU%DODQFHU7HI)ORZ3'HVLJQ
32$
EPDM ( ( ( ( ( 32$
FKM 9 9 9 9 9 32$
D 6HDO5HWDLQHU4XDG5LQJ
E 6HDO5HWDLQHU:LSLQJ6WHP6HDO 32$
F 6HDO5HWDLQHU/RZHU)OXVK4XDG5LQJ 32$
G
6HDO5HWDLQHU/RZHU)OXVK
:LSLQJ6WHP6HDO
32$
&ODPS
6SUD\%XVKLQJ
DF $GDSWHU2ULQJRU4XDG5LQJ
E $GDSWHU:LSLQJ6WHP6HDO 32$
D
2ULQJ8SSHU6WHP EPDM ( ( ( ( ( 1$
TW\UHTXLUHG FKM 9 9 9 9 9 32$
F
4XDG5LQJ8SSHU6WHP EPDM
TW\UHTXLUHG FKM
E
:LSLQJ6WHP6HDO8SSHU EPDM 32$ 32$
TW\UHTXLUHG FKM 32$ 32$
2ULQJ)OXVK EPDM ( ( ( ( ( (
FKM 9 9 9 9 9 9
6WHP$FWXDWRU16/)OXVK
3/&+
25LQJ7HI)ORZ3'HVLJQ
E
3DUW'HVFULSWLRQ
&RQWDFW)DFWRU\
6HHDFWXDWRUSDUWVOLVW