Technogym Personal Selection TUV - Default Chapter; Table of Contents

Personal Selection TÜV: Service & Maintenance Manual - rev. 1.0
Page i
Contents
1. GENERAL NOTICES...........................................................................................................................................1.1
1.1. I NTRODUCTION ................................................................................................................................................... 1.1
1.2. R ECOMMENDATIONS .......................................................................................................................................... 1.1
1.3. G ENERAL RULES FOR REPAIR PROCEDURES ........................................................................................................ 1.2
2. TECHNICAL CHARACTERISTICS..................................................................................................................2.1
2.1. P RODUCT CODE : MACHINES ................................................................................................................................2.1
2.2. C ODIFICA DI PRODOTTO : P ANCHE ...................................................................................................................... 2.1
2.3. E QUIPMENTS : MECHANICAL CHARACTERISTICS .................................................................................................. 2.3
2.3.1. D6946 – Upper Back.........................................................................................................................2.3
2.3.2. D6950 – Rotary Torso.......................................................................................................................2.3
2.3.3. D6951 – Leg Press ............................................................................................................................2.4
2.3.4. D6957 – Abdominal Crunch..............................................................................................................2.4
2.3.5. D6958 – Lower Back.........................................................................................................................2.5
2.3.6. D6971 – Vertical Traction ................................................................................................................2.5
2.3.7. D6980 – Low Row.............................................................................................................................2.6
2.3.8. D6990 – Leg Curl..............................................................................................................................2.6
2.3.9. D6991 – Leg Extension .....................................................................................................................2.7
2.4. B ENCH : MECHANICAL CHARACTERISTICS ........................................................................................................... 2.8
2.4.1. D6P915 – Crunch Bench...................................................................................................................2.8
2.4.2. D6P920 – Adjustable Bench..............................................................................................................2.8
2.5. A MBIENT SPECIFICATIONS .................................................................................................................................. 2.9
2.6. C ONFORMITY TO REGULATIONS .......................................................................................................................... 2.9
3. INSTALLING AND MOVING THE MACHINES ............................................................................................3.1
3.1. S PECIFICATIONS AND REQUIREMENTS ................................................................................................................ 3.1
3.2. M OVING ............................................................................................................................................................. 3.3
3.2.1. Moving without wheels......................................................................................................................3.3
3.2.2. Moving with wheels...........................................................................................................................3.3
4. ACCESSORIES .....................................................................................................................................................4.1
5. WHAT IF …...........................................................................................................................................................5.1
5.1. T HE WEIGHT STACK DOES NOT SLIDE SMOOTHLY ............................................................................................... 5.1
5.2. T HE WEIGHT STACK CABLE IS NOT TAUT ............................................................................................................. 5.2
5.2.1. Adjusting the tension of the cable with crimped fitting .....................................................................5.2
5.2.2. Adjusting the tension of the cable with doubling pulley....................................................................5.2
5.3. T HE MACHINE IS NOT FLAT ................................................................................................................................. 5.4
5.4. T HE LEVERS OF DUAL - AXIS MACHINES ARE NOT ALIGNED .................................................................................. 5.5
5.5. T HE SLIDING BARS OF THE L EG P RESS SEAT ARE NOT ALIGNED .......................................................................... 5.6
5.6. T HE T UBE S TART T O W ABBLE ........................................................................................................................... 5.7
6. HOW TO DISASSEMBLE THE ….....................................................................................................................6.1
6.1. F RONT WEIGHT STACK CASING ........................................................................................................................... 6.1
6.2. T OP .................................................................................................................................................................... 6.2
6.3. S EAT ON LOW MACHINES .................................................................................................................................... 6.3
6.4. S EAT ON TALL MACHINES ................................................................................................................................... 6.5
6.5. L EG P RESS S EAT ................................................................................................................................................. 6.7
6.6. E ASY START FOR TALL MACHINES ...................................................................................................................... 6.9
6.7. R ELEASE LEVER ................................................................................................................................................ 6.11
6.8. S ELECTOR SWITCH FOR ADDITIONAL WEIGHT ................................................................................................... 6.13
6.8.1. Machines with cross with crimped cable fitting .............................................................................. 6.13
6.8.2. Machines with cross with doubling pulley ......................................................................................6.14