Technogym RUN PERSONAL - General Warnings and Service Advice; Introduction and Manual Scope

RUN PERSONAL: Service & maintenance manual - rev. 3.1
Page iii
7.9. DISASSEMBLING THE CENTER HANDLEBAR AND JOYSTICK ................................................................................ 7.19
7.10. DISASSEMBLING THE MOTOR GUARD AND SIDE UPRIGHTS ................................................................................. 7.20
7.10.1. Disassembling the low kit guard .......................................................................................................... 7.20
7.10.2. Disassembling the side uprights:.......................................................................................................... 7.22
7.10.3. Disassembling the closing lower guards .............................................................................................. 7.25
7.11. DISASSEMBLING THE LOWER COMPONENTS ...................................................................................................... 7.26
7.11.1. Disassembling the ALE Drive .............................................................................................................. 7.27
7.11.2. Disassembling the elevation microswitch and the Audio/Video connectors board (B) ........................ 7.28
7.11.3. Disassembling the power supply box (C) ............................................................................................. 7.31
7.11.4. Disassembling the elevation motor (D) ................................................................................................ 7.32
7.11.5. Disassembling the Tread belt motor (E) ............................................................................................... 7.34
7.11.6. Disassembling the belt tensioner (F) .................................................................................................... 7.35
7.12. DISASSEMBLING THE TREAD BELT, RUNNING DECK AND MOTOR DRIVE-BELT ................................................... 7.36
7.13. DISASSEMBLING THE FRONT WHEELS ................................................................................................................ 7.43
7.14. DISASSEMBLING THE AUTOTRANSFORMER (VER. 110V) .................................................................................. 7.45
7.14.1. Position A ............................................................................................................................................. 7.46
7.14.2. Position B ............................................................................................................................................. 7.47
8. ADJUSTMENTS ...................................................................................................................................................... 8.1
8.1. TENSIONING A NEW TREAD BELT ........................................................................................................................ 8.1
8.2. TENSIONING A USED TREAD BELT ....................................................................................................................... 8.2
8.3. CENTERING AND ADJUSTING THE BELT ............................................................................................................... 8.3
8.4. ALIGNING THE TREAD – BELT MOTOR DRIVE-BELT .............................................................................................. 8.4
8.5. TRAVEL LIMIT MICROSWITCH POSITION .............................................................................................................. 8.5
8.6. THE MACHINE IS NOT FLAT ................................................................................................................................. 8.6
9. EQUIPMENT CONFIGURATION........................................................................................................................ 9.1
9.1. USER MENU CONFIGURATION.............................................................................................................................. 9.1
9.2. SERVICE MENU CONFIGURATION ......................................................................................................................... 9.2
9.2.1. Table of configuration parameters ......................................................................................................... 9.3
9.2.2. Register Addr.......................................................................................................................................... 9.4
9.2.2.1. Read from low kit ................................................................................................................................................................... 9.4
9.2.2.2. Register Value ........................................................................................................................................................................ 9.4
9.2.2.3. Write to low kit....................................................................................................................................................................... 9.4
9.2.3. Inverter parameters ................................................................................................................................ 9.5
10. UPDATING THE SW ............................................................................................................................................ 10.1
11. SCHEDULED MAINTENANCE ......................................................................................................................... 11.1
11.1. ORDINARY MAINTENANCE OPERATIONS ........................................................................................................... 11.2
11.1.1. Working conditions set up (Daily) ........................................................................................................ 11.2
11.1.2. External cleaning operations (Daily) ................................................................................................... 11.2
11.1.3. Internal cleaning operations (Monthly) ............................................................................................... 11.2
11.1.4. Checking the “Emergency stop” (Monthly) ......................................................................................... 11.2
11.1.5. Complete operation (six-menthly) ........................................................................................................ 11.2
11.2. EXTRA-ORDINARY MAINTENANCE OPERATIONS ............................................................................................. 11.3
11.2.1. Checking the operation of the cardiotester receiver ............................................................................ 11.3
11.2.2. Checking the operation of the hand sensor receiver ............................................................................ 11.3
11.2.3. Checking the working conditions ......................................................................................................... 11.3
11.2.4. Checking the wiring and connections .................................................................................................. 11.3
11.2.5. Checking the state of wear of tread belt and running deck .................................................................. 11.3
11.2.6. Checking the wear of the motor roller ................................................................................................. 11.3
11.2.7. Checking the state of wear of the driving roller ................................................................................... 11.4
11.2.8. Checking the shock absorbers .............................................................................................................. 11.4
11.2.9. Checking the tread belt motor drive-belt .............................................................................................. 11.4
11.2.10. Checking and centering the tread belt ................................................................................................. 11.4
12. APPENDIX ............................................................................................................................................................. 12.1
12.1. MENU PASSWORD TABLE .................................................................................................................................. 12.1