Thermal Dynamics Cutmaster 82 - Page 114

Thermal Dynamics Cutmaster 82

114 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

Corporate Headquarters

16052 Swingley Ridge Road

Suite 300

St. Louis, MO 63017

Telephone: 636-728-3000

Email: TDCSales@Thermadyne.com

www.thermadyne.com

Table of Contents

Service Manual1
Table of Contents5
Section 1:General Information9
- Notes, Cautions and Warnings9
- Important Safety Precautions9
- Publications10
- Note, Attention Et Avertissement11
- Precautions de Securite Importantes11
- Documents de Reference13
- Declaration of Conformity14
- Statement of Warranty15
Section 2 System:introduction17
- How to Use this Manual17
- Equipment Identification17
- Receipt of Equipment17
- Power Supply Specifications18
- Input Wiring Specifications19
- Power Supply Features20
Section 2 Torch:introduction21
- 01 Scope of Manual21
- 02 General Description21
- 03 Specifications21
- 04 Options and Accessories22
- 05 Introduction to Plasma22
Section 3 System: Installation25
- Unpacking25
- Lifting Options25
- Primary Input Power Connections26
- Gas Connections28
Section 3 Torch: Installation31
- 01 Torch Connections31
- 02 Setting up Mechanical Torch31
Section 4 System: Operation33
- Front Panel Controls / Features33
- Preparations for Operation34
Section 4 Torch:operation37
- 01 Torch Parts Selection37
- 02 Cut Quality38
- 03 General Cutting Information38
- T.02 Cut Quality38
- 04 Hand Torch Operation39
- 05 Gouging43
- T.05 Gouging43
- 06 Mechanized Torch Operation44
- 07 Parts Selection for Manual and Mechanized Torch Cutting45
  - T.08 Recommended Cutting Speeds for Mechanized Torch with Exposed Tip46
  - T.09 Recommended Cutting Speeds for Mechanized Torch with Shielded Tip49
Patent Information52
Section 5 System:service55
- General Maintenance55
- Maintenance Schedule56
- Common Faults56
- Fault Indicator57
- Basic Troubleshooting Guide58
- Power Supply Basic Parts Replacement60
- Circuit Fault Isolation62
- Main Input and Internal Power Problems66
- Pilot Arc Problems69
- Main Arc and Controls Problems71
- CNC Interface Problems71
- Test Procedures72
Section 5 Torch:service83
- 01 General Maintenance83
- 02 Inspection and Replacement of Consumable Torch Parts84
Section 6:Parts Lists85
- Introduction85
- Ordering Information85
- Power Supply Replacement85
- Major External Replacement Parts86
- Front Panel Replacement Parts87
- Left Side Replacement Parts88
- Right Side Replacement Parts89
- Options and Accessories90
- Replacement Parts for Hand Torch91
- Replacement Parts - for Mechanized Torches with Unshielded Leads92
- Torch Consumable Parts Manual and Mechanized Torches94
Section 7: Replacement Procedures95
- Scope95
- Anti-Static Handling Procedures95
- Parts Replacement - General Information95
- Major External Parts96
- Front Panel Parts Replacement97
- Left Side Internal Parts Replacement98
- Rear Panel Parts Replacement99
- Right Side Internal Parts Replacement101
Appendix 1: Sequence of Operation(Block Diagram103
Appendix 2: Data Tag Information104
Appendix 3: Torch Pin - out Diagrams105
Appendix 4: Torch Connection Diagrams106
Appendix 5: System Schematic, 208/460V Units108
Appendix 6: System Schematic, 600V Units110
APPENDIX 7: Publication History112

Related product manuals

Preview: Thermal Dynamics CUTMASTER 81

Thermal Dynamics CUTMASTER 81

Preview: CE CutMaster 80XL

CE CutMaster 80XL

Preview: Thermal Dynamics 81 CUTMASTER

Thermal Dynamics 81 CUTMASTER

Preview: Thermal Dynamics CUTMASTER

Thermal Dynamics CUTMASTER

Thermal Dynamics 51 CUTMASTER

Thermal Dynamics CutMaster 38

Preview: Thermal Dynamics CUTMASTER 39

Thermal Dynamics CUTMASTER 39

Preview: Thermal Dynamics CUTMASTER 60i

Thermal Dynamics CUTMASTER 60i

Preview: Thermal Dynamics CUTMASTER 151

Thermal Dynamics CUTMASTER 151

Preview: Thermal Dynamics 152 CUTMASTER

Thermal Dynamics 152 CUTMASTER

Preview: Thermal Dynamics CUTMASTER 102

Thermal Dynamics CUTMASTER 102

Preview: Thermal Dynamics CutMaster 40MM

Thermal Dynamics CutMaster 40MM