Why continuous keypad backlighting is off until a button is pressed on TriMark Locks?
The continuous keypad backlighting on your TriMark Locks is off until a button is pressed because the vehicle battery voltage has dropped below 11 V.
Why is my TriMark Control Unit experiencing intermittent operation?
If your TriMark Control Unit experiences no operation or intermittent operation, try mounting the RF receiver away from enclosed metal areas and fully extend the antenna. Also, check the FOB transmitter battery voltage; these batteries typically need replacement every 1-2 years, depending on usage.
What to do if there is no response in any system element of TriMark Locks?
If you experience no response in any system element of your TriMark Locks, verify the power to the I/O module and check the fuse.
What to do if one e-FOB function does not work on my TriMark Remote Starter?
If a specific e-FOB function on your TriMark Remote Starter isn't working, check the wire connections of the affected function at the RF module, wiring harness, and e-ASK module.
What to do if my TriMark Control Unit has no response with button press?
If there is no response when you press a button on your TriMark Control Unit, verify the connection of the keypad.
Why TriMark e-ASK lights and panic mode do not turn off with ignition start?
If the lights and panic mode on your TriMark Remote Starter do not turn off when you start the ignition, make sure that the ignition input is wired properly.
What to do if my TriMark Remote Starter has no response with button press?
If your TriMark Remote Starter has no response when you press a button, try the following: * Verify that the e-ASK module is receiving power. * Check that the keypad cable is securely connected, even though the rest of the system should function without it.
Why does the output relay latch on or off on my TriMark Security System?
If the output relay latches on or off in your TriMark Security System: * Verify that power to the external relay comes from connector J12, pin 1. * Cycle power to the system. If the condition continues, replace the external relay.
How to fix TriMark Locks when button press does not provide correct operation?
If pressing a button on your TriMark Locks system doesn't result in the correct operation, verify the power supply to both the I/O module and the RF receiver. Additionally, try re-teaching the FOB transmitter to the receiver, making sure to only press the Lock button while in learn mode.
What to do if TriMark Locks have no operation or intermittent operation?
If your TriMark Locks system exhibits no operation or intermittent operation, try these steps: Mount the RF receiver away from enclosed metal areas and fully extend the antennae. Also, check the FOB transmitter battery voltage; consider changing the batteries every 1-2 years, depending on how often you use them.
Introduces the main components of the e-ASK system: e-FOB, e-PAD, and e-ASK I/O module.
Details the different operational configurations available for the e-PAD based on DIP switch settings.
Explains the protective deactivating security feature for the e-PAD to prevent unauthorized access.
Describes the functional assignments based on S2 DIP switch settings for relay banks and system configurations.
Explains adjustable settings for timed outputs like dome/porch light and auxiliary compartment lighting.
Details the use of the S1 Learn Switch Connector for resetting keypad codes and assigning new ones.
Covers features like status LEDs and basic door locking/unlocking pulse outputs.
Describes the audible and visual feedback provided upon locking and unlocking the system.
Explains how to activate and the effects of the panic mode function.
Details the conditions under which the alarm mode is triggered and its response.
Describes the activation of the dome/porch light via keypad or FOB, and its duration control.
Provides recommendations for optimal placement and mounting of the RF receiver and I/O modules.
Explains the feature for automatic locking after engine start and unlocking when turned off.
Lists wire colors and their corresponding pin assignments for the RF receiver using various harnesses.
Details the relay output connections for locking, unlocking, and actuating different door banks.
Outlines connections for trim pots, learning inputs, keypad connectors, and power sources on the I/O board.
Presents visual diagrams illustrating actuator wiring, auxiliary outputs, and switch inputs.
Step-by-step instructions for programming additional e-FOB transmitters to the system.
Guide for resetting the keypad, assigning a new authority code, and programming access codes.
Details the process for assigning up to five different access codes to the keypad.
General| Operating Voltage | 12V DC |
|---|---|
| Remote Start | Yes |
| Keyless Entry | Yes |
| Weatherproof | Yes |
| Operating Temperature | -40°C to 85°C |
| Compatibility | Most vehicles with automatic transmissions |
| Security System | Yes |
| Number of Buttons | 5 |
To Next Page
