Vaisala WINDCAP WMT52 - Options and Accessories; Table 18 Options and Accessories

To Next Page

To Previous Page

User’s Guide ______________________________________________________________________

118 __________________________________________________________________M210925EN-B

Options and Accessories

Table 18 Options and Accessories

Description Order code

Service Pack 2: Vaisala Configuration Tool

software and USB service cable

220614

USB service cable adapter for WXT510/

WMT50

221523

2-meter cable with 8-pin M12 female

connector

222287

10-meter cable with 8-pin M12 female

connector

222288

10-meter extension cable with 8-pin M12

female and male connectors

215952

40-meter cable, open ends 217020

Bushing and Grounding kit 222109

WMT52 Bottom assembly WMTBOTTOMSP

Mounting Kit 212792

Surge Protector for sensor WSP150

Surge Protector for USB and PC WSP152

Bird Spike Kit 212793

Main Page

Default Chapter3
- Table of Contents3
Chapter 1 General Information11
- About this Manual11
- ESD Protection13
- Recycling13
- Trademarks14
- License Agreement14
- Regulatory Compliance14
- Warranty15
Chapter 2 Product Overview17
- Introduction to Ultrasonic Wind Sensor WMT5217
  - Figure 1 Ultrasonic Wind Sensor WMT5217
    - Heating Function18
- Optional Software for Easy Settings18
- Ultrasonic Wind Sensor WMT52 Components19
Chapter 3 Functional Description25
- Wind Measurement Principle25
- Heating (Optional)27
  - Figure 8 Heating Control27
Chapter 4 Installation29
- Unpacking Instructions29
- Selecting the Location30
  - Figure 9 Recommended Mast Location in an Open Area30
  - Figure 10 Recommended Mast Length on Top of a Building31
- Installation Procedure32
Chapter 5 Wiring and Power Management41
- Power Supplies41
- Wiring Using the 8-Pin M12 Connector44
Chapter 645
- Wiring Using the Screw Terminals46
  - Figure 23 Screw Terminal Block46
- Data Communication Interfaces48
  - Figure 24 Data Communication Interfaces48
- Power Management49
Chapter 6 Connection Options53
- Communication Protocols53
  - Table 3 Available Serial Communication Protocols53
- Connection Cables54
  - Table 4 Connection Cable Options54
  - Installing the Driver for the USB Cable55
- Service Cable Connection56
  - Connection through M12 Bottom Connector or Screw Terminal57
  - Table 5 Default Serial Communication Settings for M12/Screw Terminal Connection57
- Communication Setting Commands58
Chapter 7 Getting the Data Messages63
- General Commands64
  - Reset (Axz)64
  - Measurement Reset (Axzm)65
- ASCII Protocol66
- SDI-12 Protocol73
- NMEA 0183 V3.0 Protocol84
Chapter 8 Sensor and Data Message Settings97
- Wind Sensor97
- Supervisor Message103
- Composite Data Message (Ar0)106
Chapter 9 Maintenance109
- Cleaning109
- Factory Calibration and Repair Service110
- Vaisala Service Centers110
Chapter 10 Troubleshooting111
- Table 9 Data Validation111
- Table 10 Communication Problems112
- Self-Diagnostics113
Chapter 11 Technical Specifications117
- Specifications117
- Options and Accessories120
  - Table 18 Options and Accessories120
- Dimensions121
  - Figure 25 WMT52 Dimensions in MM (Inch)121
  - Figure 26 Mounting Kit Dimensions in MM (Inch)122
Appendix Anetworking123
- Connecting Several Wmt52S on the same Bus123
- SDI-12 Serial Interface123
  - Wiring123
  - Communication Protocol124
- RS-485 Serial Interface124
Appendix B Sdi-12 Protocol131
- SDI-12 Electrical Interface131
Appendix C Crc-16 Computation135
- Encoding the CRC as ASCII Characters136
- NMEA 0183 V3.0 Checksum Computation136
Appendix D137
Wind Measurement Averaging Method137
- Figure 28 Wind Measurement Averaging Method138
Appendix E Factory Configurations139
Factory Configurations139
- General Unit Settings140
- Wind Configuration Settings140
  - Table 19 General Unit Settings140
  - Table 20 Wind Configuration Settings140
- Supervisor Settings141
  - Table 21 General Unit Settings141

Vaisala WINDCAP WMT52 - Options and Accessories; Table 18 Options and Accessories

Table of Contents

Related product manuals