Why is my Vertiv Liebert 10kVA UPS showing warning code 09?
The Vertiv UPS might be showing warning code 09 because it is overloaded. Try removing some of the connected devices from the UPS output. It is also possible that the UPS is locked in Bypass mode after repetitive overloads. In this case, remove excess loads, then shut down and restart the UPS.
What to do if Vertiv Liebert 10kVA fault code 43 is shown?
If fault code 43 is displayed on your Vertiv UPS, it indicates that the UPS has been overloaded for too long and has shut down automatically. To resolve this, remove excess loads from the UPS output and then restart it.
What to do if my Vertiv UPS battery backup time is shorter than expected?
If the battery backup time of your Vertiv UPS is shorter than the nominal value, it could be due to the following reasons: * The batteries are not fully charged. Charge the batteries for at least 7 hours and then check the capacity. * The batteries are defective. In this case, contact the dealer to replace the battery.
What does it mean if my Vertiv Liebert 10kVA UPS shows fault code 14, 15, 16, 17, 18, or 19?
If your Vertiv UPS displays fault code 14, 15, 16, 17, 18, or 19, it means the UPS has automatically shut down due to a short circuit on the UPS output. Inspect the output wiring and connected devices to identify and resolve any short circuit issues.
How to fix Vertiv UPS warning code 02?
Warning code 02 on a Vertiv UPS indicates that the input neutral wire is disconnected. Check and correct the input neutral connection. If the connection is correct and the warning persists, go to the LCD setting menu, navigate to ADVANCE, then User, and then Electronic. Select “CHE” in the Neutral Line Check item and restart the UPS.
What does Vertiv UPS warning code 0B mean?
Warning code 0B on your Vertiv UPS means the EPO (Emergency Power Off) function is activated. This occurs when the EPO switch is in the “OFF” status or the jumper is open. Set the circuit in a closed position to disable the EPO function.
What does Vertiv Liebert 10kVA warning code 01 mean?
Warning code 01 on a Vertiv UPS indicates that the external or internal battery is incorrectly connected. Check to ensure all batteries are properly connected.
What does Vertiv UPS warning code 0A mean?
The warning code 0A on Vertiv UPS means that either the fan is locked or not working, or the UPS temperature is too high. Check the fans and notify your dealer.
How to troubleshoot Vertiv UPS when the front panel has no indication?
If there is no display or alarm on the front panel of your Vertiv UPS, even when the mains are normal, it might be due to the AC input power not being properly connected. Check that the input cable is firmly connected to the mains.
Guidelines for the safe and correct installation of the UPS.
Procedures and precautions for maintaining the UPS.
Step-by-step guide for installing a single UPS unit.
Instructions for installing UPS units in a parallel configuration.
Details on UPS operation when using battery power.
Instructions for operating a single UPS unit.
Guidance on setting up and operating UPS units in parallel.
List and explanation of UPS fault codes.
List and explanation of UPS warning codes.
Safety precautions and general guidance for UPS maintenance.
Information on technical support and contact details.
General| Power Rating | 10 kVA |
|---|---|
| Frequency | 50/60 Hz |
| Topology | Double Conversion Online |
| Humidity | 0-95% non-condensing |
| Input Voltage | 208/220/230/240 VAC |
| Output Voltage | 208/220/230/240 VAC |
| Battery Type | Sealed Lead-Acid (SLA) |
| Runtime | Varies based on load and battery configuration |
| Form Factor | Tower |
| Dimensions (H x W x D) | Varies by model |
| Weight | Varies by model |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -15°C to 45°C |
To Next Page