Videx VX2200 - User Manual

Other manuals for Videx VX2200

Instruction Sheet20 pages

Questions and Answers

J
Jeffrey GatesAug 29, 2025
Why won't the Videx VX2200 Intercom System panel turn on?
- R
  rkirbyAug 29, 2025
  If your Videx Intercom System is supplied with power but the VX2202/.. or VX2203/.. front panel doesn't turn on, it could be due to: 1. An interruption or short circuit of the 13Vdc output on Art.521B to the outdoor station; check the GND and +13V connections on Art.521B and on VX2202/../ VX2203/.., then check the protection fuse on the output of art.521B and change it if necessary. 2. Art.521B being defective or a blown fuse; check Art.521B power supply and in case change it or take the tension off for at least 120sec.
K
Kevin NguyenAug 28, 2025
How to stop Videx Intercom System audio from oscillating?
- I
  Isabella PetersonAug 28, 2025
  If the audio level on your Videx Intercom System is at its limit or oscillates (Larsen effect), the 'Balance' trimmer on the outdoor station might not be appropriately set, and/or the conversation volumes are programmed at a high level. Adjust the 'balance' trimmer on the outdoor station until the problem is solved, and/or lower the volumes of the microphone and loudspeaker.
D
David RiceAug 27, 2025
Why does my Videx VX2200 Intercom System show 'ERROR' and beep?
- S
  Susan RaymondAug 27, 2025
  If the VX2202/.. / VX2203/.. front panel of your Videx Intercom System displays 'ERROR' (VX2202/.. only) and emits intermittent acoustic signals every 2 seconds, here are the possible causes: 1. There might be a short circuit on the BUS '?' and 'L' line; check the BUS connections. 2. The polarity on the BUS connection of a phone, videophone, or connected accessory could be inverted; check the polarity of the device connection. 3. The VX2202/.. or VX2203/.. might be programmed as 'Slave' when it should be 'Master'; configure the device as 'Master'.
T
Tammy LloydAug 27, 2025
Why is my Videx VX2200 Intercom System conversation one-way?
- M
  Micheal LeachAug 27, 2025
  If calls go through on your Videx Intercom System, but the conversation is only one-way, the supplying voltage on the outdoor station might be too low (under 10.5V). To fix this, increase the supply wires section (GND and 13V) or double them with others available.
J
Jason RussellAug 25, 2025
How to fix low audio level in Videx VX2200?
- L
  Laura DavisAug 26, 2025
  If the audio level during conversations on your Videx Intercom System is too low, it could be that the conversation volumes in both directions are not appropriately adjusted. To resolve this, adjust the trimmers for the microphone and loudspeaker on the outdoor station to achieve the best hearing level without oscillations (Larsen effect).
A
Abigail SloanAug 25, 2025
What to do if Videx Intercom System doesn't ring and shows 'Engaged' or 'Error'?
- E
  Eric WalkerAug 25, 2025
  If your Videx Intercom System doesn't ring the extension when a call comes in, and the front panel displays 'Engaged' or 'Error' with acoustic signals, the following could be the cause: 1. The phone or videophone might not be correctly connected; check the BUS line connection. 2. The wire section (BUS) might be too small; increase the wire section or double them with others available. 3. The address programmed on the dip-switch of the phone, videophone, or accessory might not match the call; check that the address associated with the call corresponds to the one programmed on the dip-switch. 4. If a concierge is present in the system, it might have been left in programming mode; remove VX2210 from programming mode.