D-302541 39
Multi-button PowerCode transmitters transmit the same
code each time the same button is pressed. They can be
used for emergency signaling, for activating the PGM
output or for controlling appliances via X-10 units. They
can not be used for arming / disarming.
CodeSecure transmitters are of the rolling code type - they
transmit a new code each time the same button is pressed.
This provides a higher security level, especially in arming /
disarming applications, because the code can not be
copied (“grabbed”) by unauthorized people.
Following are the basic details of several compatible
transmitters. The possible applications for each push-
button are indicated in each drawing.
A. MCT-234
One-way 4-button PowerCode
'keyfob' transmitter. You can
program the AUX (auxiliary)
button to perform various
tasks, in accordance with the
user’s needs.
Pressing AWAY and HOME
together for 2 sec. initiates
PANIC alarm. Pressing
AWAY twice for 2 sec.
initiates Latchkey arming.
DISARM
AWAY
AUX
HOME
MCT-234
B. MCT-237
Two-way CodeSecure 6-
button ‘Keyfob’ transmitter.
You can program the AUX
(auxiliary) buttons to perform
various tasks, in accordance
with the user’s needs.
Pressing AWAY and HOME
together for 2 sec. initiates
PANIC alarm. Pressing
AWAY twice within 2 sec.
initiates Latchkey arming.
DISPLAY
DISARM
STATUS /
PARTITION
AUX 2
AUX 1
HOME
AWAY
MCT-237
C. MCT-231 / 201*
(N.A. in North America)
Single-button pendant units.
The MCT-231 (Code- Secure)
and the MCT-201
(PowerCode) can be enrolled
to perform functions as shown.
Both units look alike.
MCT-231 / 201
D. MCT-134 / 104*
(N.A. in North America) 4-
button hand-held units. MCT-
134 (CodeSecure) can replace
the MCT-234 keyfob. MCT-
104 (PowerCode) can perform
emergency and non- alarm
functions. Both units look alike.
MCT-134 / 104
E. MCT-132 / 102*
(N.A. in North America) 2-
button units. MCT-132
(CodeSecure) can perform
functions as shown.
MCT-
102 (PowerCode) can
perform emergency and non-
alarm tasks. Both units look
alike.
MCT-132 / 102
F. MCT-131 / 101*
(N.A. in North America) Single-
button units. The MCT-131
(CodeSecure) and the MCT-
101 (PowerCode) can be
enrolled to perform functions as
shown. Both units look alike.
MCT-131 / 101
G. MCT-211*
Water-proof,
wrist-worn Power
-Code transmitter. Can be
enrolled to perform emergency
or non-alarm functions.
MCT-211
H. MCM 140+
The MCM-140+ is a wireless
remote control unit that
enables the user to
arm/disarm the alarm system,
to initiate
emergency/fire/panic alarms,
to perform one of the AUX
functions, to turn lighting
devices on and off, and for
PGM control. The keypad
includes an RF transmitter
that sends out a differently
coded RF signal for each
command.
MCM-140+
I. MKP-150/151
The MKP-150 / MKP-151
operates using two-way
encrypted coded
transmission and provides
aural and visual indications.
For each control panel, a
maximum of two MKP-150 /
MKP-151 keypad devices
may be enrolled.
The device enables the user to
arm/disarm the alarm system,
to initiate emergency / fire /
panic alarms and to turn lighting
devices on and off.
AWAY
MKP-150/151
* Not UL listed.
E3 Compatible WL Siren
The MCS-710 / MCS-720 /
MCS-730 (*) wireless siren can
be integrated with the
PowerMax Pro in areas in which
wiring action is difficult or
impossible. The MCS-710 /
MCS-720 / MCS-730 is a fully
supervised, 2-way
communication device (it
includes a receiver, to receive
activation commands from the
alarm system, and a transmitter
to periodically transmit its status
signal to the alarm system).
When an identifiable activation
command is received from the
PowerMax Pro, the siren activates
its sounder and the flash light
(strobe light every 1.5 seconds).
* Not UL listed.
MCS-710
MCS-720
MCS-730
To Next Page
Loading...
Need help?
General
