Watson-Marlow 630 U - Flow Sensor Reading

Watson-Marlow 630 U

186 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

23.5 Flow Sensor Reading

The flow sensor value can be read via the Flow sensor reading screen

126 m-630un-en-08

Table of Contents

Default Chapter1
- Table of Contents1
1 Declaration of Conformity5
2 Declaration of Incorporation6
3 When You Unpack Your Pump7
- Unpacking Your Pump7
- Packaging Disposal7
- Inspection7
- Components Supplied7
- Storage7
4 Information for Returning Pumps8
5 Peristaltic Pumps - an Overview8
6 Warranty9
7 Safety Notes10
8 Pump Specifications13
- Specification Ratings13
- Weights13
- Pumphead Options14
9 Good Pump Installation Practice15
- General Recommendations15
- Dos and Don'ts16
10 Pump Operation17
- Keypad Layout and Key Ids17
- Starting and Stopping18
- Using up and down Keys18
- Maximum Speed18
- Change Rotation Direction18
11 Connecting to a Power Supply19
- Conductor Colour Coding20
- Wiring the US NEMA Module20
- Wiring the NEMA Module20
- Earth Screening of Control Cables on NEMA Module20
- Ethernet M12 Connector Screen Connection22
12 Start-Up Check List23
13 Control Wiring24
- Upper D-Connector24
- Lower D-Connector24
- Standard - 25 Way D: Inputs and Outputs24
- Standard - 25 Way D: Power Supply Limits32
- N - Modules Standard and SCADA32
- Standard N - Module33
- SCADA N-Module38
14 Control Wiring49
- Pump External Interface Parameters50
- Features on the Rear of the Pump51
- IP31 Wiring Connections52
- Sensor Wiring - IP3152
- IP66 Wiring - N Module56
- Input/Output Connectors - IP6660
- Network Topology62
15 Switching the Pump on for the First Time63
- Selecting the Display Language63
- First-Time Start-Up Defaults65
16 Switching the Pump on in Subsequent Power Cycles67
17 Mode Menu68
18 Manual69
- Start69
- Stop70
- Increasing and Decreasing Flow Rate71
- MAX FUNCTION (Manual Mode Only)72
19 Flow Calibration73
- Setting the Flow Calibration73
20 Analog Mode76
- Analog Calibration77
- Calibrate Input78
- Setting a High Signal79
- Setting High Flow Calibration80
- Setting a Low Signal81
- Setting Low Flow Calibration82
21 Memodose Mode84
- To Configure Memodose84
- Set Flow Rate84
- Resume Interrupted Doses85
- Master Dose86
- Manual Dosing89
22 Ethernet/Ip™ Mode90
- Configure Ethernet/Ip™ Settings90
- Ethernet/Ip™ Mode94
- Example for Http Connection between Pump and PC (Peer-To-Peer)94
- Setting up the PC95
- Connecting the PC to the Pump96
- Connecting Using the Web Browser97
- Connecting to a PLC97
- Pump Parameters101
23 Sensors113
- Sensor Wiring113
- Setting up the Sensors114
- Start up Delay118
- Generic Sensors120
- Flow Sensor Reading126
24 Main Menu127
- Security Settings129
- General Settings140
- Control Settings150
- Configure Outputs153
- Configure Inputs154
25 Help159
26 Troubleshooting160
- Leak Detection161
- Error Codes161
- Technical Support162
27 Drive Maintenance163
28 Drive Spares164
29 Pumphead Replacement165
30 Tube Replacement167
- Continuous Tubing167
- Tube Elements168
31 Ordering Information170
- Pump Part Numbers170
- Tubing and Element Part Numbers171
- CIP and SIP Procedures175
- Pumphead Spares176
32 Performance Data180
- 620RE, 620RE4 and 620R Performance Data180
33 Trademarks184
34 Disclaimers185
35 Publication History186

Related product manuals

Watson-Marlow 630 UN

Preview: Watson-Marlow 630 Bp

Watson-Marlow 630 Bp

Preview: Watson-Marlow 630 Du

Watson-Marlow 630 Du

Watson-Marlow 730 U

Preview: Watson-Marlow 620RA

Watson-Marlow 620RA

Preview: Watson-Marlow 620DuN

Watson-Marlow 620DuN

Preview: Watson-Marlow 323E

Watson-Marlow 323E

Watson-Marlow 323Du

Watson-Marlow qdos60

Preview: Watson-Marlow qdos30

Watson-Marlow qdos30

Preview: Watson-Marlow 530 Bp

Watson-Marlow 530 Bp

Preview: Watson-Marlow 530 Du

Watson-Marlow 530 Du