Watson-Marlow 630 U - Page 145

Watson-Marlow 630 U

186 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Pumphead type

Select GENERAL SETTINGS from the main menu.

Use the ∧ /∨ keys to move the selection bar over Pumphead type and press SELECT. The following

screen will be displayed.

Use the ∧ /∨ keys to move the selection bar over Pumphead and press SELECT.

m-630un-en-08 145

Table of Contents

Default Chapter1
- Table of Contents1
1 Declaration of Conformity5
2 Declaration of Incorporation6
3 When You Unpack Your Pump7
- Unpacking Your Pump7
- Packaging Disposal7
- Inspection7
- Components Supplied7
- Storage7
4 Information for Returning Pumps8
5 Peristaltic Pumps - an Overview8
6 Warranty9
7 Safety Notes10
8 Pump Specifications13
- Specification Ratings13
- Weights13
- Pumphead Options14
9 Good Pump Installation Practice15
- General Recommendations15
- Dos and Don'ts16
10 Pump Operation17
- Keypad Layout and Key Ids17
- Starting and Stopping18
- Using up and down Keys18
- Maximum Speed18
- Change Rotation Direction18
11 Connecting to a Power Supply19
- Conductor Colour Coding20
- Wiring the US NEMA Module20
- Wiring the NEMA Module20
- Earth Screening of Control Cables on NEMA Module20
- Ethernet M12 Connector Screen Connection22
12 Start-Up Check List23
13 Control Wiring24
- Upper D-Connector24
- Lower D-Connector24
- Standard - 25 Way D: Inputs and Outputs24
- Standard - 25 Way D: Power Supply Limits32
- N - Modules Standard and SCADA32
- Standard N - Module33
- SCADA N-Module38
14 Control Wiring49
- Pump External Interface Parameters50
- Features on the Rear of the Pump51
- IP31 Wiring Connections52
- Sensor Wiring - IP3152
- IP66 Wiring - N Module56
- Input/Output Connectors - IP6660
- Network Topology62
15 Switching the Pump on for the First Time63
- Selecting the Display Language63
- First-Time Start-Up Defaults65
16 Switching the Pump on in Subsequent Power Cycles67
17 Mode Menu68
18 Manual69
- Start69
- Stop70
- Increasing and Decreasing Flow Rate71
- MAX FUNCTION (Manual Mode Only)72
19 Flow Calibration73
- Setting the Flow Calibration73
20 Analog Mode76
- Analog Calibration77
- Calibrate Input78
- Setting a High Signal79
- Setting High Flow Calibration80
- Setting a Low Signal81
- Setting Low Flow Calibration82
21 Memodose Mode84
- To Configure Memodose84
- Set Flow Rate84
- Resume Interrupted Doses85
- Master Dose86
- Manual Dosing89
22 Ethernet/Ip™ Mode90
- Configure Ethernet/Ip™ Settings90
- Ethernet/Ip™ Mode94
- Example for Http Connection between Pump and PC (Peer-To-Peer)94
- Setting up the PC95
- Connecting the PC to the Pump96
- Connecting Using the Web Browser97
- Connecting to a PLC97
- Pump Parameters101
23 Sensors113
- Sensor Wiring113
- Setting up the Sensors114
- Start up Delay118
- Generic Sensors120
- Flow Sensor Reading126
24 Main Menu127
- Security Settings129
- General Settings140
- Control Settings150
- Configure Outputs153
- Configure Inputs154
25 Help159
26 Troubleshooting160
- Leak Detection161
- Error Codes161
- Technical Support162
27 Drive Maintenance163
28 Drive Spares164
29 Pumphead Replacement165
30 Tube Replacement167
- Continuous Tubing167
- Tube Elements168
31 Ordering Information170
- Pump Part Numbers170
- Tubing and Element Part Numbers171
- CIP and SIP Procedures175
- Pumphead Spares176
32 Performance Data180
- 620RE, 620RE4 and 620R Performance Data180
33 Trademarks184
34 Disclaimers185
35 Publication History186

Related product manuals

Watson-Marlow 630 UN

Preview: Watson-Marlow 630 Bp

Watson-Marlow 630 Bp

Watson-Marlow 730 U

Preview: Watson-Marlow 620DuN

Watson-Marlow 620DuN

Preview: Watson-Marlow 120

Watson-Marlow 120

Preview: Watson-Marlow 323E

Watson-Marlow 323E

Watson-Marlow qdos60

Preview: Watson-Marlow qdos30

Watson-Marlow qdos30

Preview: Watson-Marlow 530 Bp

Watson-Marlow 530 Bp

Preview: Watson-Marlow 530 Du

Watson-Marlow 530 Du

Preview: Watson-Marlow 730 Bp

Watson-Marlow 730 Bp

Watson-Marlow qdos120