Yaesu FT-2000D User Manual

Page 36 FT-2000D OPERATING MANUAL
+
CLAR
Main Tuning Dial knob
[
ANTENNA
]
Button
[
MODE
]
Button
[
SQL
]
Knob
Sub
[
SQL
]
Knob
[
A/B
]
Button
(
VFO-A
) [
BAND
]
Button
(
VFO-A
) [
MHz
]
Button
[
FAST
]
Button
(
VFO-B
) [
BAND
]
Button
(
VFO-B
) [
MHz
]
Button
[
SUB VFO-B
]
Knob
1. Set the FP-2000’s
[
POWER
]
switch to “I” position.
2. Press and hold in the FT-2000D’s
[
POWER
]
switch for one second
to turn the transceiver on.
3. The transceiver will start up on 7.000.00
MHz LSB, and normal operation may begin.
NOTE:
To turn power off, press and hold in the FT-2000D’s
[
POWER
]
switch for one second.
4. Rotate the
[
AF GAIN
]
knob to set
a comfortable audio level on incom-
ing signals or noise. Clockwise ro-
tation of the
[
AF GAIN
]
knob in-
creases the volume level.
NOTE:
When using headphones, start by rotating the
[
AF
GAIN
]
knob counter-clockwise, then bring the volume
level up after you put the headphones on. This will
minimize the chance of damage to your hearing caused
by an unexpectedly-high audio level.
5. Press the Main
[
RX
]
but-
ton to engage the Main
(VFO-A) receiver; the
imbedded LED will glow
Green.
ADVICE
::
::
:
 If you press the Main
[
RX
]
button when the imbedded LED is already
glowing Green, the LED will now blink on and off;
this indicates that the Main (VFO-A) receiver is
temporarily muted. Just press the Main
[
RX
]
but-
ton once more to restore Main (VFO-A) receiver
operation.
 Press the Sub
[
RX
]
button to
engage Dual Reception (us-
ing the Sub (VFO-B) re-
ceiver in addition to the
Main (VFO-A) receiver).
When you press the Sub
[
RX
]
button, its imbedded LED
will glow green; pressing this
button once more will turn off
the Sub (VFO-B) receiver, and
the imbeded LED will go dark.
Use the Sub receiver’s Sub
[
AF
GAIN
]
knob to adjust the Sub
(VFO-B) receiver volume level.
6. Press the
[
BAND
]
but-
ton corresponding to
the Amateur band on
which you wish to be-
gin operation.
ADVICE
::
::
:
 One-touch selec-
tion of each Ama-
teur band between
1.8 and 50 MHz is provided.
 The FT-2000D utilizes a triple band-stack VFO
selection technique, which permits you to store up
to three favorite frequencies and modes onto each
band’s VFO register. For example, you may store
one frequency each on 14 MHz CW, RTTY, and
USB, then recall these VFOs by successive, mo-
mentary presses of the
[
14
]
MHz band button. Each
Amateur band button may similarly have up to three
frequency/mode settings applied.
[
POWER
]
Switch
Main
[
RX
]
Button
[
AF GAIN
]
Knob
Sub
[
AF GAIN
]
Knob
[
BAND
]
Button
Sub
[
RX
]
Button
BASIC OPERATION:RECEIVING ON AMATEUR BANDS
Here is the typical start-up procedure for normal operation:

Yaesu FT-2000D Specifications

General

Brand	Yaesu
Model	FT-2000D
Category	Transceiver
Language	English