What does 'Unknown USB' mean on my Yamaha Stereo System?
The 'Unknown USB' message indicates that the connected USB device is either not playable on the unit or the file name is too long. Use a compatible USB device, and ensure file names are no more than 250 characters.
Why is there no sound from my Yamaha Media Player when using iPod?
First, ensure the iPod is firmly set in the iPod dock. Also, check if headphones are connected and remove them. Finally, make sure your iPod software is up to date by downloading the latest iTunes software.
What to do if my Yamaha Media Player system is suddenly turned off?
The unit may have turned off automatically. This unit automatically turns off the system 60 minutes after USB device or CD playback is stopped. Also, check if the sleep function is enabled and turn the system back on. If the AUTO POWER OFF function is triggered, setting AUTO POWER OFF to TIME OFF enables continuous play.
What to do if my Yamaha Media Player does not operate properly?
The unit may have experienced a strong electrical shock or a drop in power supply. To resolve this, turn the system off and disconnect the power cable. Wait about 30 seconds, then reconnect the power cable and turn the system back on.
What to do if my Yamaha Media Player playback does not start immediately?
The disc might be dirty, so wipe it clean. Also, the disc loaded into the unit may not be compatible, so use a supported disc. If the unit was moved from a cold to warm place, condensation may have formed on the disc reading lens; wait for an hour or two until the unit adjusts to room temperature.
What does "Over Current" mean on my Yamaha Media Player?
The USB device might be connected at an angle. Disconnect the USB device, turn the system off and on again, and then reconnect the USB device correctly.
Why is there a delay when pressing play on my Yamaha Stereo System?
A delay in playback after pressing play may be due to a dirty or incompatible disc, or condensation on the disc reading lens. Wipe the disc clean, use a supported disc, or wait an hour or two for the unit to adjust to room temperature.
Why does my Yamaha Stereo System say 'No Files' for USB?
If your Yamaha Stereo System displays 'No Files' when a USB device is connected, it means the USB device does not contain playable files. Use a USB device that contains playable files.
How to stop digital equipment from producing noises on Yamaha TSX-112 Stereo System?
If your Yamaha Stereo System is picking up noise from digital or high-frequency equipment, it might be placed too close to the equipment. Try placing the unit farther away.
What does it mean when the clock flashes and the Yamaha TSX-112 Stereo System cannot be operated?
If the clock is flashing and your Yamaha Stereo System cannot be operated, the CLOCK on the rear panel might be set to SET, indicating that the unit is in clock setting mode. Set CLOCK on the rear panel to ON.
General| Impedance | 6 Ω |
|---|---|
| Driver diameter | 110 mm |
| Frequency range | - Hz |
| RMS rated power | 30 W |
| Audio output channels | 2.0 channels |
| AUX in | Yes |
| Bluetooth | No |
| Headphone connectivity | 3.5 mm |
| USB 2.0 ports quantity | 1 |
| Dimensions (WxDxH) | 457 x 174 x 181 mm |
| USB connector type | USB Type-A |
| Supported radio bands | DAB, DAB+, FM |
| Preset stations quantity | 60 |
| Built-in charger | - |
| Power source type | AC |
| Product color | Black |
| Apple docking compatibility | iPhone, iPod |
Weight and Dimensions| Weight | 5100 g |
|---|
Important safety instructions and precautions for operating the unit.
Instructions on how to connect and set up an iPod in the unit's dock.
How to select and play music from a connected iPod.
Guidance on playing music from CDs and USB devices.
Initial scan procedure required before tuning into DAB stations.
Steps to tune into DAB radio stations using manual or automatic methods.
How to save and select favorite DAB radio stations using presets.
Steps to tune into FM radio stations using automatic or manual methods.
How to save and select favorite FM radio stations using presets.
Explains the alarm types, including SRC+BEEP, SOURCE, and BEEP.
Step-by-step guide to setting the alarm time, sound, and source.
To Next Page
