YASKAWA V1000 Replacing Guide

VAN-V19001E [V1000→GA500]
10/35
3-2. Control Circuit Terminals and Signal Levels
For both the V1000 and GA500, the functions shown are factory defaults.
Differences in specification between the V1000 and the GA500 are highlighted in bold.
Table 6: Control Circuit Terminal Matching Table
Analog Input
Name
Signal Level
V1000
GA500
V1000
GA500
S1
S1
MFDI selection 1
(ON: Forward run, OFF: Stop)
Photocoupler isolation
24 VDC, 8 mA
Photocoupler isolation
24 VDC, 6 mA
S2
S2
MFDI selection 2
(ON: Reverse run, OFF: Stop)
S3
S3
MFDI selection 3 (External fault (N.O.))
S4
S4
MFDI selection 4 (Fault reset)
S5
S5
MFDI selection 5 (Multi-step speed
reference 1)
S6
S6
MFDI selection 6 (Multi-step speed
reference 2)
S7
S7
MFDI selection 7 (Jog command)
SN
MFDI power supply 0 V
MFDI power supply, 24 V
(maximum 150 mA)
*3
SC
*1
SC
MFDI selection common
Sequence common *2
SP
MFDI power supply +24 Vdc
RP
RP
Master frequency reference pulse train
input
 Response frequency
0.5 to 32kHz
 H level duty: 30% to 70%
 H level voltage:
3.5 V to 13.2 V
 L level voltage: 0.0 V to
0.8 V
 Input impedance: 3kΩ
 Response frequency:
0 to 32kHz
 H level duty: 30% to
70%
 H level voltage:
3.5 V to 13.2 V
 L level voltage: 0.0 V to
0.8 V
 Input impedance: 3kΩ
+V
+V
Power supply for frequency setting
+10.5 V (allowable current 20 mA maximum)
A1
A1
MFAI1
 Voltage input: DC0 to
+10 V (20kΩ)
 Resolution: 1/1000
 Voltage input: DC0 to
+10 V (20kΩ)
 Resolution: 1/4096
A2
A2
MFAI2
 0 V to 10 V/100% (input
impedance: 20 kΩ),
resolution: 1/1000
 4 mA to 20 mA/100%, 0
mA to 20 mA (input
impedance: 250 Ω),
resolution: 1/500
*4
 0 V to 10 V/100% (input
impedance: 20 kΩ),
resolution: 1/4096
 4 mA to 20 mA/100%, 0
mA to 20 mA (input
impedance: 250 Ω),
resolution: 1/2048
*4
AC
AC
Frequency reference common
0V
E(G)
E(G)
Cable sheath
For option card earth wire connection
-

YASKAWA V1000 Specifications

General

Input Voltage	3-Phase 200-240VAC, 3-Phase 380-480VAC
Output Voltage	3-Phase 200-240VAC, 3-Phase 380-480VAC
Output Frequency	0-400 Hz
Control Method	V/f control
Overload Capacity	150% for 60 seconds
Protection Functions	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit, Ground Fault
Communication Options	Modbus RTU
Ambient Temperature	-10 to +50°C (14 to 122°F)
Storage Temperature	-20°C to +65°C (-4°F to 149°F)
Humidity	95% (non-condensing)
Cooling Method	Forced Air Cooling
Enclosure	IP20