Yealink SIP-T31G Administrator's Guide

Administrator’s Guide for SIP-T2 /T3 /T4 /T5 /CP920 IP Phones
397
Topics
Call Hold Configuration
Music on Hold (MoH) Configuration
Call Hold Configuration
The following table lists the parameters you can use to configure call hold.
Parameter
sip.rfc2543_hold <y0000000000xx>.cfg
Description
It enables or disables the phone to use RFC 2543 (c=0.0.0.0) outgoing hold signaling.
Permitted
Values
0-Disabled, SDP media direction attributes (such as a=sendonly) per RFC 3264 is used when placing
a call on hold.
1-Enabled, SDP media connection address c=0.0.0.0 per RFC 2543 is used when placing a call on
hold.
Default
0
Web UI
Features > General Information > RFC 2543 Hold
Parameter
account.X.hold_use_inactive
[1]
<MAC>.cfg
Description
It enables or disables the phone to use inactive outgoing hold signaling.
Note: It works only if “sip.rfc2543_hold" is set to 0 (Disabled).
Permitted
Values
0-Disabled, SDP media direction attribute “a=sendonly” is used when placing a call on hold.
1-Enabled, SDP media direction attribute “a=inactive” is used when placing a call on hold. RTP pack-
ets will not be sent or received.
Default
0
Parameter
features.play_hold_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to play the call hold tone when you place a call on hold.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Web UI
Features > General Information > Play Hold Tone
Parameter
features.play_hold_tone.delay <y0000000000xx>.cfg
Description
It configures the time (in seconds) to wait for the phone to play the initial call hold tone.
If it is set to 30 (30s), the phone will wait 30 seconds to play the initial call hold tone after you place a
call on hold.
Note: It works only if “features.play_hold_tone.enable” is set to 1 (Enabled).
Permitted
Values
Integer from 3 to 3600
Default
30
Web UI
Features > General Information > Play Hold Tone Delay
Parameter
features.play_hold_tone.interval <y0000000000xx>.cfg
Description
It configures the time (in seconds) between subsequent call hold tones.
If it is set to 3 (3s) and “features.play_hold_tone.delay” is set to 30 (30s), the phone will begin to play a
hold tone after you place a call on hold for 30 seconds, and repeat the call hold tone every 3 seconds.

Yealink SIP-T31G Specifications

General

Mounting kit	Yes
Number of handles included	1 pc(s)
Display diagonal	2.3 \
Display resolution	132 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	G.722, G.729, AGC, G.729A, AJB, PLC, G.711Mu, VAD, G.711a, G.723.1, G.726, iLBC, CNG, OPUS
AC adapter input voltage	100 - 240 V
AC adapter output current	0.6 A
AC adapter output voltage	5 V
Power consumption (typical)	3 W
Lines quantity	2 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	2
Sustainability certificates	RoHS, REACH
Networking standards	IEEE 802.3af, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1x
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	188 mm
Height	162 mm
Package depth	210 mm
Package width	213 mm
Package height	103 mm