Yealink SIP-T31G Administrator's Guide

Administrator’s Guide for SIP-T2 /T3 /T4 /T5 /CP920 IP Phones
455
Devices
Parameter
blf.enhanced.parked.talking.action <y0000000000xx>.cfg
Description
It configures the behavior when pressing the BLF/BLF list DSS key if the monitor is talking and a call is
parked against the monitored phone.
This value uses the same macro action string syntax as an Enhanced DSS key.
Example:
blf.enhanced.parked.talking.action = newcall
Note: It works only if “blf.enhanced.parked.enable” is set to 1 (Enabled).
Permitted
Values
String
Default
Blank
Supported
Devices
All phones except T30P, T30, T19(P) E2 and CP920
Parameter
blf.enhanced.parked.idle.action <y0000000000xx>.cfg
Description
It configures the behavior when pressing the BLF/BLF list DSS key if the monitor is idle and a call is
parked against the monitored phone.
This value uses the same macro action string syntax as an Enhanced DSS key.
Example:
blf.enhanced.parked.idle.action = newcall
Note: It works only if “blf.enhanced.parked.enable” is set to 1 (Enabled).
Permitted
Values
String
Default
Blank
Supported
Devices
All phones except T30P, T30, T19(P) E2 and CP920
BLF Key LED/Icon and Behavior for Hold State Configuration
The following table lists the parameters you can use to configure BLF key LED/icon and Behavior for hold state (the
call on the monitored phone is placed on hold).
Parameter
blf.enhanced.hold.enable <y0000000000xx>.cfg
Description
It enables or disables the custom configuration when the call on the monitored phone is placed on
hold.
Permitted
Values
0-Disabled
1-Enabled, the phone will display the custom BLF/BLF List DSS key LED status/icon colors.
Default
0
Supported
Devices
All phones except T48G, T46G, T42G, T41P, T30P, T30, T29G, T19(P) E2 and CP920
Parameter
blf.enhanced.hold.led <y0000000000xx>.cfg
Description
It configures the custom BLF/BLF List DSS key LED status/icon colors when the call on the monitored
phone is placed on hold.
This value uses the same macro action string syntax as an Enhanced DSS key.

Yealink SIP-T31G Specifications

General

Mounting kit	Yes
Number of handles included	1 pc(s)
Display diagonal	2.3 \
Display resolution	132 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	G.722, G.729, AGC, G.729A, AJB, PLC, G.711Mu, VAD, G.711a, G.723.1, G.726, iLBC, CNG, OPUS
AC adapter input voltage	100 - 240 V
AC adapter output current	0.6 A
AC adapter output voltage	5 V
Power consumption (typical)	3 W
Lines quantity	2 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	2
Sustainability certificates	RoHS, REACH
Networking standards	IEEE 802.3af, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1x
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	188 mm
Height	162 mm
Package depth	210 mm
Package width	213 mm
Package height	103 mm