:CALCulate:AMARker[1|2|3|4]:MINimum:
NEXT
Function Detects the lowest bottom whose level is
greater than or equal to that of the current
specified advanced marker position and sets
the specified advanced marker there.
Syntax
:CALCulate:AMARker[1|2|3|4]:MINimum
:NEXT
[1|2|3|4]: Advanced marker number
Example
:CALCULATE:AMARKER:MINIMUM:NEXT
Description • If the specified advanced marker has not been
assigned, a moving marker will be assigned.
• If the advanced marker number is not
specified, advanced marker 1 will be used.
• This is a sequential command.
• This command can be used on the AQ6370C/
AQ6370D/AQ6373B/AQ6375B.
:CALCulate:AMARker[1|2|3|4]:MINimum:
RIGHt
Function Detects the closest bottom to the right of the
current specified advanced marker position and
sets the specified advanced marker there.
Syntax
:CALCulate:AMARker[1|2|3|4]:MINimum
:RIGHt
[1|2|3|4]: Advanced marker number
Example
:CALCULATE:AMARKER:MINIMUM:RIGHT
Description • If the specified advanced marker has not been
assigned, a moving marker will be assigned.
• If the advanced marker number is not
specified, advanced marker 1 will be used.
• This is a sequential command.
• This command can be used on the AQ6370C/
AQ6370D/AQ6373B/AQ6375B.
:CALCulate:AMARker[1|2|3|4][:STATe]
Function Sets or queries whether the specified advanced
marker is to be assigned.
Also queries the status of the specified moving
marker.
Syntax
:CALCulate:AMARker[1|2|3|4]
[:STATe]<wsp>OFF|ON|0|1
:CALCulate:AMARker[1|2|3|4]
[:STATe]?
[1|2|3|4]: Advanced marker number
Response 0 = Off, 1 = On
Example
:CALCULATE:AMARKER ON
:CALCULATE:AMARKER? -> 1
Description • If a moving marker is assigned, power
spectral density markers (:CALCulate:AMAR
ker[1|2|3|4]:FUNCtion:PDENsity|:NOISe[:STA
Te]) and integrated power markers (:CALCula
te:AMARker[1|2|3|4]:FUNCtion:INTegral[:STA
Te]) will be set to off.
• If the advanced marker number is not
specified, advanced marker 1 will be used.
• This is a sequential command.
• This command can be used on the AQ6370C/
AQ6370D/AQ6373B/AQ6375B.
:CALCulate:AMARker[1|2|3|4]:TRACe
Function Sets or queries the trace that the specified
advanced marker is assigned to.
Syntax
:CALCulate:AMARker[1|2|3|4]:TRACe<w
sp><trace name>
:CALCulate:AMARker[1|2|3|4]:TRACe?
[1|2|3|4]: Advanced marker number
<trace name> = Trace
TRA to TRG = Trace A to trace G
Example
:CALCULATE:AMARKER:TRACE TRA
:CALCULATE:AMARKER:TRACE? -> TRA
Description • Setting and querying are possible even when
the specified advanced marker has not been
assigned.
• If the advanced marker number is not
specified, advanced marker 1 will be used.
• This is a sequential command.
• This command can be used on the AQ6370C/
AQ6370D/AQ6373B/AQ6375B.
:CALCulate:AMARker[1|2|3|4]:X
Function Sets the specified advanced marker to the
specified position.
Also queries the X value of the specified
advanced marker.
Syntax
:CALCulate:AMARker[1|2|3|4]:X<wsp><
NRf>[M|HZ]
:CALCulate:AMARker[1|2|3|4]:X?
[1|2|3|4]: Advanced marker number
<NRf> = Advanced marker position
Response <NRf> = Advanced marker position
Example
:CALCULATE:AMARKER:X 1550.000nm
:CALCULATE:AMARKER:X? ->
+1.55000000E-006
Description • The unit of the returned advanced
marker X value depends on the
:CALCulate:MARKer:UNIT setting.
• The unit of the returned advanced marker level
depends on the :CALCulate:MARKer:UNIT
setting.
• If this set command is used when the
specified advanced marker has not been
assigned, a moving marker will be assigned.
• If a query is made when the specified
advanced marker has not been assigned, a
query error will occur.
• If the advanced marker number is not
specified, advanced marker 1 will be used.
• This is a sequential command.
• This command can be used on the AQ6370C/
AQ6370D/AQ6373B/AQ6375B.
7.6 Instrument-Specific Commands
To Next Page
Loading...
Need help?
General
